diff --git a/Documentation/ABI/testing/sysfs-class-regulator b/Documentation/ABI/testing/sysfs-class-regulator new file mode 100644 index 0000000..79a4a75 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-regulator @@ -0,0 +1,315 @@ +What: /sys/class/regulator/.../state +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + state. This holds the regulator output state. + + This will be one of the following strings: + + 'enabled' + 'disabled' + 'unknown' + + 'enabled' means the regulator output is ON and is supplying + power to the system. + + 'disabled' means the regulator output is OFF and is not + supplying power to the system.. + + 'unknown' means software cannot determine the state. + + NOTE: this field can be used in conjunction with microvolts + and microamps to determine regulator output levels. + + +What: /sys/class/regulator/.../type +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + type. This holds the regulator type. + + This will be one of the following strings: + + 'voltage' + 'current' + 'unknown' + + 'voltage' means the regulator output voltage can be controlled + by software. + + 'current' means the regulator output current limit can be + controlled by software. + + 'unknown' means software cannot control either voltage or + current limit. + + +What: /sys/class/regulator/.../microvolts +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + microvolts. This holds the regulator output voltage setting + measured in microvolts (i.e. E-6 Volts). + + NOTE: This value should not be used to determine the regulator + output voltage level as this value is the same regardless of + whether the regulator is enabled or disabled. + + +What: /sys/class/regulator/.../microamps +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + microamps. This holds the regulator output current limit + setting measured in microamps (i.e. E-6 Amps). + + NOTE: This value should not be used to determine the regulator + output current level as this value is the same regardless of + whether the regulator is enabled or disabled. + + +What: /sys/class/regulator/.../opmode +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + opmode. This holds the regulator operating mode setting. + + The opmode value can be one of the following strings: + + 'fast' + 'normal' + 'idle' + 'standby' + 'unknown' + + The modes are described in include/linux/regulator/regulator.h + + NOTE: This value should not be used to determine the regulator + output operating mode as this value is the same regardless of + whether the regulator is enabled or disabled. + + +What: /sys/class/regulator/.../min_microvolts +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + min_microvolts. This holds the minimum safe working regulator + output voltage setting for this domain measured in microvolts. + + NOTE: this will return the string 'constraint not defined' if + the power domain has no min microvolts constraint defined by + platform code. + + +What: /sys/class/regulator/.../max_microvolts +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + max_microvolts. This holds the maximum safe working regulator + output voltage setting for this domain measured in microvolts. + + NOTE: this will return the string 'constraint not defined' if + the power domain has no max microvolts constraint defined by + platform code. + + +What: /sys/class/regulator/.../min_microamps +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + min_microamps. This holds the minimum safe working regulator + output current limit setting for this domain measured in + microamps. + + NOTE: this will return the string 'constraint not defined' if + the power domain has no min microamps constraint defined by + platform code. + + +What: /sys/class/regulator/.../max_microamps +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + max_microamps. This holds the maximum safe working regulator + output current limit setting for this domain measured in + microamps. + + NOTE: this will return the string 'constraint not defined' if + the power domain has no max microamps constraint defined by + platform code. + + +What: /sys/class/regulator/.../num_users +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + num_users. This holds the number of consumer devices that + have called regulator_enable() on this regulator. + + +What: /sys/class/regulator/.../requested_microamps +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + requested_microamps. This holds the total requested load + current in microamps for this regulator from all its consumer + devices. + + +What: /sys/class/regulator/.../parent +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Some regulator directories will contain a link called parent. + This points to the parent or supply regulator if one exists. + +What: /sys/class/regulator/.../suspend_mem_microvolts +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_mem_microvolts. This holds the regulator output + voltage setting for this domain measured in microvolts when + the system is suspended to memory. + + NOTE: this will return the string 'not defined' if + the power domain has no suspend to memory voltage defined by + platform code. + +What: /sys/class/regulator/.../suspend_disk_microvolts +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_disk_microvolts. This holds the regulator output + voltage setting for this domain measured in microvolts when + the system is suspended to disk. + + NOTE: this will return the string 'not defined' if + the power domain has no suspend to disk voltage defined by + platform code. + +What: /sys/class/regulator/.../suspend_standby_microvolts +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_standby_microvolts. This holds the regulator output + voltage setting for this domain measured in microvolts when + the system is suspended to standby. + + NOTE: this will return the string 'not defined' if + the power domain has no suspend to standby voltage defined by + platform code. + +What: /sys/class/regulator/.../suspend_mem_mode +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_mem_mode. This holds the regulator operating mode + setting for this domain when the system is suspended to + memory. + + NOTE: this will return the string 'not defined' if + the power domain has no suspend to memory mode defined by + platform code. + +What: /sys/class/regulator/.../suspend_disk_mode +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_disk_mode. This holds the regulator operating mode + setting for this domain when the system is suspended to disk. + + NOTE: this will return the string 'not defined' if + the power domain has no suspend to disk mode defined by + platform code. + +What: /sys/class/regulator/.../suspend_standby_mode +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_standby_mode. This holds the regulator operating mode + setting for this domain when the system is suspended to + standby. + + NOTE: this will return the string 'not defined' if + the power domain has no suspend to standby mode defined by + platform code. + +What: /sys/class/regulator/.../suspend_mem_state +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_mem_state. This holds the regulator operating state + when suspended to memory. + + This will be one of the following strings: + + 'enabled' + 'disabled' + 'not defined' + +What: /sys/class/regulator/.../suspend_disk_state +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_disk_state. This holds the regulator operating state + when suspended to disk. + + This will be one of the following strings: + + 'enabled' + 'disabled' + 'not defined' + +What: /sys/class/regulator/.../suspend_standby_state +Date: May 2008 +KernelVersion: 2.6.26 +Contact: Liam Girdwood +Description: + Each regulator directory will contain a field called + suspend_standby_state. This holds the regulator operating + state when suspended to standby. + + This will be one of the following strings: + + 'enabled' + 'disabled' + 'not defined' diff --git a/Documentation/DocBook/kgdb.tmpl b/Documentation/DocBook/kgdb.tmpl index e8acd1f..372dec2 100644 --- a/Documentation/DocBook/kgdb.tmpl +++ b/Documentation/DocBook/kgdb.tmpl @@ -98,6 +98,24 @@ "Kernel debugging" select "KGDB: kernel debugging with remote gdb". + It is advised, but not required that you turn on the + CONFIG_FRAME_POINTER kernel option. This option inserts code to + into the compiled executable which saves the frame information in + registers or on the stack at different points which will allow a + debugger such as gdb to more accurately construct stack back traces + while debugging the kernel. + + + If the architecture that you are using supports the kernel option + CONFIG_DEBUG_RODATA, you should consider turning it off. This + option will prevent the use of software breakpoints because it + marks certain regions of the kernel's memory space as read-only. + If kgdb supports it for the architecture you are using, you can + use hardware breakpoints if you desire to run with the + CONFIG_DEBUG_RODATA option turned on, else you need to turn off + this option. + + Next you should choose one of more I/O drivers to interconnect debugging host and debugged target. Early boot debugging requires a KGDB I/O driver that supports early debugging and the driver must be diff --git a/Documentation/filesystems/configfs/configfs.txt b/Documentation/filesystems/configfs/configfs.txt index 44c97e6..fabcb0e 100644 --- a/Documentation/filesystems/configfs/configfs.txt +++ b/Documentation/filesystems/configfs/configfs.txt @@ -311,9 +311,20 @@ the subsystem must be ready for it. [An Example] The best example of these basic concepts is the simple_children -subsystem/group and the simple_child item in configfs_example.c It -shows a trivial object displaying and storing an attribute, and a simple -group creating and destroying these children. +subsystem/group and the simple_child item in configfs_example_explicit.c +and configfs_example_macros.c. It shows a trivial object displaying and +storing an attribute, and a simple group creating and destroying these +children. + +The only difference between configfs_example_explicit.c and +configfs_example_macros.c is how the attributes of the childless item +are defined. The childless item has extended attributes, each with +their own show()/store() operation. This follows a convention commonly +used in sysfs. configfs_example_explicit.c creates these attributes +by explicitly defining the structures involved. Conversely +configfs_example_macros.c uses some convenience macros from configfs.h +to define the attributes. These macros are similar to their sysfs +counterparts. [Hierarchy Navigation and the Subsystem Mutex] diff --git a/Documentation/filesystems/configfs/configfs_example.c b/Documentation/filesystems/configfs/configfs_example.c deleted file mode 100644 index 0396487..0000000 --- a/Documentation/filesystems/configfs/configfs_example.c +++ /dev/null @@ -1,485 +0,0 @@ -/* - * vim: noexpandtab ts=8 sts=0 sw=8: - * - * configfs_example.c - This file is a demonstration module containing - * a number of configfs subsystems. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public - * License as published by the Free Software Foundation; either - * version 2 of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public - * License along with this program; if not, write to the - * Free Software Foundation, Inc., 59 Temple Place - Suite 330, - * Boston, MA 021110-1307, USA. - * - * Based on sysfs: - * sysfs is Copyright (C) 2001, 2002, 2003 Patrick Mochel - * - * configfs Copyright (C) 2005 Oracle. All rights reserved. - */ - -#include -#include -#include - -#include - - - -/* - * 01-childless - * - * This first example is a childless subsystem. It cannot create - * any config_items. It just has attributes. - * - * Note that we are enclosing the configfs_subsystem inside a container. - * This is not necessary if a subsystem has no attributes directly - * on the subsystem. See the next example, 02-simple-children, for - * such a subsystem. - */ - -struct childless { - struct configfs_subsystem subsys; - int showme; - int storeme; -}; - -struct childless_attribute { - struct configfs_attribute attr; - ssize_t (*show)(struct childless *, char *); - ssize_t (*store)(struct childless *, const char *, size_t); -}; - -static inline struct childless *to_childless(struct config_item *item) -{ - return item ? container_of(to_configfs_subsystem(to_config_group(item)), struct childless, subsys) : NULL; -} - -static ssize_t childless_showme_read(struct childless *childless, - char *page) -{ - ssize_t pos; - - pos = sprintf(page, "%d\n", childless->showme); - childless->showme++; - - return pos; -} - -static ssize_t childless_storeme_read(struct childless *childless, - char *page) -{ - return sprintf(page, "%d\n", childless->storeme); -} - -static ssize_t childless_storeme_write(struct childless *childless, - const char *page, - size_t count) -{ - unsigned long tmp; - char *p = (char *) page; - - tmp = simple_strtoul(p, &p, 10); - if (!p || (*p && (*p != '\n'))) - return -EINVAL; - - if (tmp > INT_MAX) - return -ERANGE; - - childless->storeme = tmp; - - return count; -} - -static ssize_t childless_description_read(struct childless *childless, - char *page) -{ - return sprintf(page, -"[01-childless]\n" -"\n" -"The childless subsystem is the simplest possible subsystem in\n" -"configfs. It does not support the creation of child config_items.\n" -"It only has a few attributes. In fact, it isn't much different\n" -"than a directory in /proc.\n"); -} - -static struct childless_attribute childless_attr_showme = { - .attr = { .ca_owner = THIS_MODULE, .ca_name = "showme", .ca_mode = S_IRUGO }, - .show = childless_showme_read, -}; -static struct childless_attribute childless_attr_storeme = { - .attr = { .ca_owner = THIS_MODULE, .ca_name = "storeme", .ca_mode = S_IRUGO | S_IWUSR }, - .show = childless_storeme_read, - .store = childless_storeme_write, -}; -static struct childless_attribute childless_attr_description = { - .attr = { .ca_owner = THIS_MODULE, .ca_name = "description", .ca_mode = S_IRUGO }, - .show = childless_description_read, -}; - -static struct configfs_attribute *childless_attrs[] = { - &childless_attr_showme.attr, - &childless_attr_storeme.attr, - &childless_attr_description.attr, - NULL, -}; - -static ssize_t childless_attr_show(struct config_item *item, - struct configfs_attribute *attr, - char *page) -{ - struct childless *childless = to_childless(item); - struct childless_attribute *childless_attr = - container_of(attr, struct childless_attribute, attr); - ssize_t ret = 0; - - if (childless_attr->show) - ret = childless_attr->show(childless, page); - return ret; -} - -static ssize_t childless_attr_store(struct config_item *item, - struct configfs_attribute *attr, - const char *page, size_t count) -{ - struct childless *childless = to_childless(item); - struct childless_attribute *childless_attr = - container_of(attr, struct childless_attribute, attr); - ssize_t ret = -EINVAL; - - if (childless_attr->store) - ret = childless_attr->store(childless, page, count); - return ret; -} - -static struct configfs_item_operations childless_item_ops = { - .show_attribute = childless_attr_show, - .store_attribute = childless_attr_store, -}; - -static struct config_item_type childless_type = { - .ct_item_ops = &childless_item_ops, - .ct_attrs = childless_attrs, - .ct_owner = THIS_MODULE, -}; - -static struct childless childless_subsys = { - .subsys = { - .su_group = { - .cg_item = { - .ci_namebuf = "01-childless", - .ci_type = &childless_type, - }, - }, - }, -}; - - -/* ----------------------------------------------------------------- */ - -/* - * 02-simple-children - * - * This example merely has a simple one-attribute child. Note that - * there is no extra attribute structure, as the child's attribute is - * known from the get-go. Also, there is no container for the - * subsystem, as it has no attributes of its own. - */ - -struct simple_child { - struct config_item item; - int storeme; -}; - -static inline struct simple_child *to_simple_child(struct config_item *item) -{ - return item ? container_of(item, struct simple_child, item) : NULL; -} - -static struct configfs_attribute simple_child_attr_storeme = { - .ca_owner = THIS_MODULE, - .ca_name = "storeme", - .ca_mode = S_IRUGO | S_IWUSR, -}; - -static struct configfs_attribute *simple_child_attrs[] = { - &simple_child_attr_storeme, - NULL, -}; - -static ssize_t simple_child_attr_show(struct config_item *item, - struct configfs_attribute *attr, - char *page) -{ - ssize_t count; - struct simple_child *simple_child = to_simple_child(item); - - count = sprintf(page, "%d\n", simple_child->storeme); - - return count; -} - -static ssize_t simple_child_attr_store(struct config_item *item, - struct configfs_attribute *attr, - const char *page, size_t count) -{ - struct simple_child *simple_child = to_simple_child(item); - unsigned long tmp; - char *p = (char *) page; - - tmp = simple_strtoul(p, &p, 10); - if (!p || (*p && (*p != '\n'))) - return -EINVAL; - - if (tmp > INT_MAX) - return -ERANGE; - - simple_child->storeme = tmp; - - return count; -} - -static void simple_child_release(struct config_item *item) -{ - kfree(to_simple_child(item)); -} - -static struct configfs_item_operations simple_child_item_ops = { - .release = simple_child_release, - .show_attribute = simple_child_attr_show, - .store_attribute = simple_child_attr_store, -}; - -static struct config_item_type simple_child_type = { - .ct_item_ops = &simple_child_item_ops, - .ct_attrs = simple_child_attrs, - .ct_owner = THIS_MODULE, -}; - - -struct simple_children { - struct config_group group; -}; - -static inline struct simple_children *to_simple_children(struct config_item *item) -{ - return item ? container_of(to_config_group(item), struct simple_children, group) : NULL; -} - -static struct config_item *simple_children_make_item(struct config_group *group, const char *name) -{ - struct simple_child *simple_child; - - simple_child = kzalloc(sizeof(struct simple_child), GFP_KERNEL); - if (!simple_child) - return ERR_PTR(-ENOMEM); - - - config_item_init_type_name(&simple_child->item, name, - &simple_child_type); - - simple_child->storeme = 0; - - return &simple_child->item; -} - -static struct configfs_attribute simple_children_attr_description = { - .ca_owner = THIS_MODULE, - .ca_name = "description", - .ca_mode = S_IRUGO, -}; - -static struct configfs_attribute *simple_children_attrs[] = { - &simple_children_attr_description, - NULL, -}; - -static ssize_t simple_children_attr_show(struct config_item *item, - struct configfs_attribute *attr, - char *page) -{ - return sprintf(page, -"[02-simple-children]\n" -"\n" -"This subsystem allows the creation of child config_items. These\n" -"items have only one attribute that is readable and writeable.\n"); -} - -static void simple_children_release(struct config_item *item) -{ - kfree(to_simple_children(item)); -} - -static struct configfs_item_operations simple_children_item_ops = { - .release = simple_children_release, - .show_attribute = simple_children_attr_show, -}; - -/* - * Note that, since no extra work is required on ->drop_item(), - * no ->drop_item() is provided. - */ -static struct configfs_group_operations simple_children_group_ops = { - .make_item = simple_children_make_item, -}; - -static struct config_item_type simple_children_type = { - .ct_item_ops = &simple_children_item_ops, - .ct_group_ops = &simple_children_group_ops, - .ct_attrs = simple_children_attrs, - .ct_owner = THIS_MODULE, -}; - -static struct configfs_subsystem simple_children_subsys = { - .su_group = { - .cg_item = { - .ci_namebuf = "02-simple-children", - .ci_type = &simple_children_type, - }, - }, -}; - - -/* ----------------------------------------------------------------- */ - -/* - * 03-group-children - * - * This example reuses the simple_children group from above. However, - * the simple_children group is not the subsystem itself, it is a - * child of the subsystem. Creation of a group in the subsystem creates - * a new simple_children group. That group can then have simple_child - * children of its own. - */ - -static struct config_group *group_children_make_group(struct config_group *group, const char *name) -{ - struct simple_children *simple_children; - - simple_children = kzalloc(sizeof(struct simple_children), - GFP_KERNEL); - if (!simple_children) - return ERR_PTR(-ENOMEM); - - - config_group_init_type_name(&simple_children->group, name, - &simple_children_type); - - return &simple_children->group; -} - -static struct configfs_attribute group_children_attr_description = { - .ca_owner = THIS_MODULE, - .ca_name = "description", - .ca_mode = S_IRUGO, -}; - -static struct configfs_attribute *group_children_attrs[] = { - &group_children_attr_description, - NULL, -}; - -static ssize_t group_children_attr_show(struct config_item *item, - struct configfs_attribute *attr, - char *page) -{ - return sprintf(page, -"[03-group-children]\n" -"\n" -"This subsystem allows the creation of child config_groups. These\n" -"groups are like the subsystem simple-children.\n"); -} - -static struct configfs_item_operations group_children_item_ops = { - .show_attribute = group_children_attr_show, -}; - -/* - * Note that, since no extra work is required on ->drop_item(), - * no ->drop_item() is provided. - */ -static struct configfs_group_operations group_children_group_ops = { - .make_group = group_children_make_group, -}; - -static struct config_item_type group_children_type = { - .ct_item_ops = &group_children_item_ops, - .ct_group_ops = &group_children_group_ops, - .ct_attrs = group_children_attrs, - .ct_owner = THIS_MODULE, -}; - -static struct configfs_subsystem group_children_subsys = { - .su_group = { - .cg_item = { - .ci_namebuf = "03-group-children", - .ci_type = &group_children_type, - }, - }, -}; - -/* ----------------------------------------------------------------- */ - -/* - * We're now done with our subsystem definitions. - * For convenience in this module, here's a list of them all. It - * allows the init function to easily register them. Most modules - * will only have one subsystem, and will only call register_subsystem - * on it directly. - */ -static struct configfs_subsystem *example_subsys[] = { - &childless_subsys.subsys, - &simple_children_subsys, - &group_children_subsys, - NULL, -}; - -static int __init configfs_example_init(void) -{ - int ret; - int i; - struct configfs_subsystem *subsys; - - for (i = 0; example_subsys[i]; i++) { - subsys = example_subsys[i]; - - config_group_init(&subsys->su_group); - mutex_init(&subsys->su_mutex); - ret = configfs_register_subsystem(subsys); - if (ret) { - printk(KERN_ERR "Error %d while registering subsystem %s\n", - ret, - subsys->su_group.cg_item.ci_namebuf); - goto out_unregister; - } - } - - return 0; - -out_unregister: - for (; i >= 0; i--) { - configfs_unregister_subsystem(example_subsys[i]); - } - - return ret; -} - -static void __exit configfs_example_exit(void) -{ - int i; - - for (i = 0; example_subsys[i]; i++) { - configfs_unregister_subsystem(example_subsys[i]); - } -} - -module_init(configfs_example_init); -module_exit(configfs_example_exit); -MODULE_LICENSE("GPL"); diff --git a/Documentation/filesystems/configfs/configfs_example_explicit.c b/Documentation/filesystems/configfs/configfs_example_explicit.c new file mode 100644 index 0000000..d428cc9 --- /dev/null +++ b/Documentation/filesystems/configfs/configfs_example_explicit.c @@ -0,0 +1,485 @@ +/* + * vim: noexpandtab ts=8 sts=0 sw=8: + * + * configfs_example_explicit.c - This file is a demonstration module + * containing a number of configfs subsystems. It explicitly defines + * each structure without using the helper macros defined in + * configfs.h. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public + * License as published by the Free Software Foundation; either + * version 2 of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this program; if not, write to the + * Free Software Foundation, Inc., 59 Temple Place - Suite 330, + * Boston, MA 021110-1307, USA. + * + * Based on sysfs: + * sysfs is Copyright (C) 2001, 2002, 2003 Patrick Mochel + * + * configfs Copyright (C) 2005 Oracle. All rights reserved. + */ + +#include +#include +#include + +#include + + + +/* + * 01-childless + * + * This first example is a childless subsystem. It cannot create + * any config_items. It just has attributes. + * + * Note that we are enclosing the configfs_subsystem inside a container. + * This is not necessary if a subsystem has no attributes directly + * on the subsystem. See the next example, 02-simple-children, for + * such a subsystem. + */ + +struct childless { + struct configfs_subsystem subsys; + int showme; + int storeme; +}; + +struct childless_attribute { + struct configfs_attribute attr; + ssize_t (*show)(struct childless *, char *); + ssize_t (*store)(struct childless *, const char *, size_t); +}; + +static inline struct childless *to_childless(struct config_item *item) +{ + return item ? container_of(to_configfs_subsystem(to_config_group(item)), struct childless, subsys) : NULL; +} + +static ssize_t childless_showme_read(struct childless *childless, + char *page) +{ + ssize_t pos; + + pos = sprintf(page, "%d\n", childless->showme); + childless->showme++; + + return pos; +} + +static ssize_t childless_storeme_read(struct childless *childless, + char *page) +{ + return sprintf(page, "%d\n", childless->storeme); +} + +static ssize_t childless_storeme_write(struct childless *childless, + const char *page, + size_t count) +{ + unsigned long tmp; + char *p = (char *) page; + + tmp = simple_strtoul(p, &p, 10); + if (!p || (*p && (*p != '\n'))) + return -EINVAL; + + if (tmp > INT_MAX) + return -ERANGE; + + childless->storeme = tmp; + + return count; +} + +static ssize_t childless_description_read(struct childless *childless, + char *page) +{ + return sprintf(page, +"[01-childless]\n" +"\n" +"The childless subsystem is the simplest possible subsystem in\n" +"configfs. It does not support the creation of child config_items.\n" +"It only has a few attributes. In fact, it isn't much different\n" +"than a directory in /proc.\n"); +} + +static struct childless_attribute childless_attr_showme = { + .attr = { .ca_owner = THIS_MODULE, .ca_name = "showme", .ca_mode = S_IRUGO }, + .show = childless_showme_read, +}; +static struct childless_attribute childless_attr_storeme = { + .attr = { .ca_owner = THIS_MODULE, .ca_name = "storeme", .ca_mode = S_IRUGO | S_IWUSR }, + .show = childless_storeme_read, + .store = childless_storeme_write, +}; +static struct childless_attribute childless_attr_description = { + .attr = { .ca_owner = THIS_MODULE, .ca_name = "description", .ca_mode = S_IRUGO }, + .show = childless_description_read, +}; + +static struct configfs_attribute *childless_attrs[] = { + &childless_attr_showme.attr, + &childless_attr_storeme.attr, + &childless_attr_description.attr, + NULL, +}; + +static ssize_t childless_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + struct childless *childless = to_childless(item); + struct childless_attribute *childless_attr = + container_of(attr, struct childless_attribute, attr); + ssize_t ret = 0; + + if (childless_attr->show) + ret = childless_attr->show(childless, page); + return ret; +} + +static ssize_t childless_attr_store(struct config_item *item, + struct configfs_attribute *attr, + const char *page, size_t count) +{ + struct childless *childless = to_childless(item); + struct childless_attribute *childless_attr = + container_of(attr, struct childless_attribute, attr); + ssize_t ret = -EINVAL; + + if (childless_attr->store) + ret = childless_attr->store(childless, page, count); + return ret; +} + +static struct configfs_item_operations childless_item_ops = { + .show_attribute = childless_attr_show, + .store_attribute = childless_attr_store, +}; + +static struct config_item_type childless_type = { + .ct_item_ops = &childless_item_ops, + .ct_attrs = childless_attrs, + .ct_owner = THIS_MODULE, +}; + +static struct childless childless_subsys = { + .subsys = { + .su_group = { + .cg_item = { + .ci_namebuf = "01-childless", + .ci_type = &childless_type, + }, + }, + }, +}; + + +/* ----------------------------------------------------------------- */ + +/* + * 02-simple-children + * + * This example merely has a simple one-attribute child. Note that + * there is no extra attribute structure, as the child's attribute is + * known from the get-go. Also, there is no container for the + * subsystem, as it has no attributes of its own. + */ + +struct simple_child { + struct config_item item; + int storeme; +}; + +static inline struct simple_child *to_simple_child(struct config_item *item) +{ + return item ? container_of(item, struct simple_child, item) : NULL; +} + +static struct configfs_attribute simple_child_attr_storeme = { + .ca_owner = THIS_MODULE, + .ca_name = "storeme", + .ca_mode = S_IRUGO | S_IWUSR, +}; + +static struct configfs_attribute *simple_child_attrs[] = { + &simple_child_attr_storeme, + NULL, +}; + +static ssize_t simple_child_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + ssize_t count; + struct simple_child *simple_child = to_simple_child(item); + + count = sprintf(page, "%d\n", simple_child->storeme); + + return count; +} + +static ssize_t simple_child_attr_store(struct config_item *item, + struct configfs_attribute *attr, + const char *page, size_t count) +{ + struct simple_child *simple_child = to_simple_child(item); + unsigned long tmp; + char *p = (char *) page; + + tmp = simple_strtoul(p, &p, 10); + if (!p || (*p && (*p != '\n'))) + return -EINVAL; + + if (tmp > INT_MAX) + return -ERANGE; + + simple_child->storeme = tmp; + + return count; +} + +static void simple_child_release(struct config_item *item) +{ + kfree(to_simple_child(item)); +} + +static struct configfs_item_operations simple_child_item_ops = { + .release = simple_child_release, + .show_attribute = simple_child_attr_show, + .store_attribute = simple_child_attr_store, +}; + +static struct config_item_type simple_child_type = { + .ct_item_ops = &simple_child_item_ops, + .ct_attrs = simple_child_attrs, + .ct_owner = THIS_MODULE, +}; + + +struct simple_children { + struct config_group group; +}; + +static inline struct simple_children *to_simple_children(struct config_item *item) +{ + return item ? container_of(to_config_group(item), struct simple_children, group) : NULL; +} + +static struct config_item *simple_children_make_item(struct config_group *group, const char *name) +{ + struct simple_child *simple_child; + + simple_child = kzalloc(sizeof(struct simple_child), GFP_KERNEL); + if (!simple_child) + return ERR_PTR(-ENOMEM); + + config_item_init_type_name(&simple_child->item, name, + &simple_child_type); + + simple_child->storeme = 0; + + return &simple_child->item; +} + +static struct configfs_attribute simple_children_attr_description = { + .ca_owner = THIS_MODULE, + .ca_name = "description", + .ca_mode = S_IRUGO, +}; + +static struct configfs_attribute *simple_children_attrs[] = { + &simple_children_attr_description, + NULL, +}; + +static ssize_t simple_children_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + return sprintf(page, +"[02-simple-children]\n" +"\n" +"This subsystem allows the creation of child config_items. These\n" +"items have only one attribute that is readable and writeable.\n"); +} + +static void simple_children_release(struct config_item *item) +{ + kfree(to_simple_children(item)); +} + +static struct configfs_item_operations simple_children_item_ops = { + .release = simple_children_release, + .show_attribute = simple_children_attr_show, +}; + +/* + * Note that, since no extra work is required on ->drop_item(), + * no ->drop_item() is provided. + */ +static struct configfs_group_operations simple_children_group_ops = { + .make_item = simple_children_make_item, +}; + +static struct config_item_type simple_children_type = { + .ct_item_ops = &simple_children_item_ops, + .ct_group_ops = &simple_children_group_ops, + .ct_attrs = simple_children_attrs, + .ct_owner = THIS_MODULE, +}; + +static struct configfs_subsystem simple_children_subsys = { + .su_group = { + .cg_item = { + .ci_namebuf = "02-simple-children", + .ci_type = &simple_children_type, + }, + }, +}; + + +/* ----------------------------------------------------------------- */ + +/* + * 03-group-children + * + * This example reuses the simple_children group from above. However, + * the simple_children group is not the subsystem itself, it is a + * child of the subsystem. Creation of a group in the subsystem creates + * a new simple_children group. That group can then have simple_child + * children of its own. + */ + +static struct config_group *group_children_make_group(struct config_group *group, const char *name) +{ + struct simple_children *simple_children; + + simple_children = kzalloc(sizeof(struct simple_children), + GFP_KERNEL); + if (!simple_children) + return ERR_PTR(-ENOMEM); + + config_group_init_type_name(&simple_children->group, name, + &simple_children_type); + + return &simple_children->group; +} + +static struct configfs_attribute group_children_attr_description = { + .ca_owner = THIS_MODULE, + .ca_name = "description", + .ca_mode = S_IRUGO, +}; + +static struct configfs_attribute *group_children_attrs[] = { + &group_children_attr_description, + NULL, +}; + +static ssize_t group_children_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + return sprintf(page, +"[03-group-children]\n" +"\n" +"This subsystem allows the creation of child config_groups. These\n" +"groups are like the subsystem simple-children.\n"); +} + +static struct configfs_item_operations group_children_item_ops = { + .show_attribute = group_children_attr_show, +}; + +/* + * Note that, since no extra work is required on ->drop_item(), + * no ->drop_item() is provided. + */ +static struct configfs_group_operations group_children_group_ops = { + .make_group = group_children_make_group, +}; + +static struct config_item_type group_children_type = { + .ct_item_ops = &group_children_item_ops, + .ct_group_ops = &group_children_group_ops, + .ct_attrs = group_children_attrs, + .ct_owner = THIS_MODULE, +}; + +static struct configfs_subsystem group_children_subsys = { + .su_group = { + .cg_item = { + .ci_namebuf = "03-group-children", + .ci_type = &group_children_type, + }, + }, +}; + +/* ----------------------------------------------------------------- */ + +/* + * We're now done with our subsystem definitions. + * For convenience in this module, here's a list of them all. It + * allows the init function to easily register them. Most modules + * will only have one subsystem, and will only call register_subsystem + * on it directly. + */ +static struct configfs_subsystem *example_subsys[] = { + &childless_subsys.subsys, + &simple_children_subsys, + &group_children_subsys, + NULL, +}; + +static int __init configfs_example_init(void) +{ + int ret; + int i; + struct configfs_subsystem *subsys; + + for (i = 0; example_subsys[i]; i++) { + subsys = example_subsys[i]; + + config_group_init(&subsys->su_group); + mutex_init(&subsys->su_mutex); + ret = configfs_register_subsystem(subsys); + if (ret) { + printk(KERN_ERR "Error %d while registering subsystem %s\n", + ret, + subsys->su_group.cg_item.ci_namebuf); + goto out_unregister; + } + } + + return 0; + +out_unregister: + for (; i >= 0; i--) { + configfs_unregister_subsystem(example_subsys[i]); + } + + return ret; +} + +static void __exit configfs_example_exit(void) +{ + int i; + + for (i = 0; example_subsys[i]; i++) { + configfs_unregister_subsystem(example_subsys[i]); + } +} + +module_init(configfs_example_init); +module_exit(configfs_example_exit); +MODULE_LICENSE("GPL"); diff --git a/Documentation/filesystems/configfs/configfs_example_macros.c b/Documentation/filesystems/configfs/configfs_example_macros.c new file mode 100644 index 0000000..d8e30a0 --- /dev/null +++ b/Documentation/filesystems/configfs/configfs_example_macros.c @@ -0,0 +1,448 @@ +/* + * vim: noexpandtab ts=8 sts=0 sw=8: + * + * configfs_example_macros.c - This file is a demonstration module + * containing a number of configfs subsystems. It uses the helper + * macros defined by configfs.h + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public + * License as published by the Free Software Foundation; either + * version 2 of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this program; if not, write to the + * Free Software Foundation, Inc., 59 Temple Place - Suite 330, + * Boston, MA 021110-1307, USA. + * + * Based on sysfs: + * sysfs is Copyright (C) 2001, 2002, 2003 Patrick Mochel + * + * configfs Copyright (C) 2005 Oracle. All rights reserved. + */ + +#include +#include +#include + +#include + + + +/* + * 01-childless + * + * This first example is a childless subsystem. It cannot create + * any config_items. It just has attributes. + * + * Note that we are enclosing the configfs_subsystem inside a container. + * This is not necessary if a subsystem has no attributes directly + * on the subsystem. See the next example, 02-simple-children, for + * such a subsystem. + */ + +struct childless { + struct configfs_subsystem subsys; + int showme; + int storeme; +}; + +static inline struct childless *to_childless(struct config_item *item) +{ + return item ? container_of(to_configfs_subsystem(to_config_group(item)), struct childless, subsys) : NULL; +} + +CONFIGFS_ATTR_STRUCT(childless); +#define CHILDLESS_ATTR(_name, _mode, _show, _store) \ +struct childless_attribute childless_attr_##_name = __CONFIGFS_ATTR(_name, _mode, _show, _store) +#define CHILDLESS_ATTR_RO(_name, _show) \ +struct childless_attribute childless_attr_##_name = __CONFIGFS_ATTR_RO(_name, _show); + +static ssize_t childless_showme_read(struct childless *childless, + char *page) +{ + ssize_t pos; + + pos = sprintf(page, "%d\n", childless->showme); + childless->showme++; + + return pos; +} + +static ssize_t childless_storeme_read(struct childless *childless, + char *page) +{ + return sprintf(page, "%d\n", childless->storeme); +} + +static ssize_t childless_storeme_write(struct childless *childless, + const char *page, + size_t count) +{ + unsigned long tmp; + char *p = (char *) page; + + tmp = simple_strtoul(p, &p, 10); + if (!p || (*p && (*p != '\n'))) + return -EINVAL; + + if (tmp > INT_MAX) + return -ERANGE; + + childless->storeme = tmp; + + return count; +} + +static ssize_t childless_description_read(struct childless *childless, + char *page) +{ + return sprintf(page, +"[01-childless]\n" +"\n" +"The childless subsystem is the simplest possible subsystem in\n" +"configfs. It does not support the creation of child config_items.\n" +"It only has a few attributes. In fact, it isn't much different\n" +"than a directory in /proc.\n"); +} + +CHILDLESS_ATTR_RO(showme, childless_showme_read); +CHILDLESS_ATTR(storeme, S_IRUGO | S_IWUSR, childless_storeme_read, + childless_storeme_write); +CHILDLESS_ATTR_RO(description, childless_description_read); + +static struct configfs_attribute *childless_attrs[] = { + &childless_attr_showme.attr, + &childless_attr_storeme.attr, + &childless_attr_description.attr, + NULL, +}; + +CONFIGFS_ATTR_OPS(childless); +static struct configfs_item_operations childless_item_ops = { + .show_attribute = childless_attr_show, + .store_attribute = childless_attr_store, +}; + +static struct config_item_type childless_type = { + .ct_item_ops = &childless_item_ops, + .ct_attrs = childless_attrs, + .ct_owner = THIS_MODULE, +}; + +static struct childless childless_subsys = { + .subsys = { + .su_group = { + .cg_item = { + .ci_namebuf = "01-childless", + .ci_type = &childless_type, + }, + }, + }, +}; + + +/* ----------------------------------------------------------------- */ + +/* + * 02-simple-children + * + * This example merely has a simple one-attribute child. Note that + * there is no extra attribute structure, as the child's attribute is + * known from the get-go. Also, there is no container for the + * subsystem, as it has no attributes of its own. + */ + +struct simple_child { + struct config_item item; + int storeme; +}; + +static inline struct simple_child *to_simple_child(struct config_item *item) +{ + return item ? container_of(item, struct simple_child, item) : NULL; +} + +static struct configfs_attribute simple_child_attr_storeme = { + .ca_owner = THIS_MODULE, + .ca_name = "storeme", + .ca_mode = S_IRUGO | S_IWUSR, +}; + +static struct configfs_attribute *simple_child_attrs[] = { + &simple_child_attr_storeme, + NULL, +}; + +static ssize_t simple_child_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + ssize_t count; + struct simple_child *simple_child = to_simple_child(item); + + count = sprintf(page, "%d\n", simple_child->storeme); + + return count; +} + +static ssize_t simple_child_attr_store(struct config_item *item, + struct configfs_attribute *attr, + const char *page, size_t count) +{ + struct simple_child *simple_child = to_simple_child(item); + unsigned long tmp; + char *p = (char *) page; + + tmp = simple_strtoul(p, &p, 10); + if (!p || (*p && (*p != '\n'))) + return -EINVAL; + + if (tmp > INT_MAX) + return -ERANGE; + + simple_child->storeme = tmp; + + return count; +} + +static void simple_child_release(struct config_item *item) +{ + kfree(to_simple_child(item)); +} + +static struct configfs_item_operations simple_child_item_ops = { + .release = simple_child_release, + .show_attribute = simple_child_attr_show, + .store_attribute = simple_child_attr_store, +}; + +static struct config_item_type simple_child_type = { + .ct_item_ops = &simple_child_item_ops, + .ct_attrs = simple_child_attrs, + .ct_owner = THIS_MODULE, +}; + + +struct simple_children { + struct config_group group; +}; + +static inline struct simple_children *to_simple_children(struct config_item *item) +{ + return item ? container_of(to_config_group(item), struct simple_children, group) : NULL; +} + +static struct config_item *simple_children_make_item(struct config_group *group, const char *name) +{ + struct simple_child *simple_child; + + simple_child = kzalloc(sizeof(struct simple_child), GFP_KERNEL); + if (!simple_child) + return ERR_PTR(-ENOMEM); + + config_item_init_type_name(&simple_child->item, name, + &simple_child_type); + + simple_child->storeme = 0; + + return &simple_child->item; +} + +static struct configfs_attribute simple_children_attr_description = { + .ca_owner = THIS_MODULE, + .ca_name = "description", + .ca_mode = S_IRUGO, +}; + +static struct configfs_attribute *simple_children_attrs[] = { + &simple_children_attr_description, + NULL, +}; + +static ssize_t simple_children_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + return sprintf(page, +"[02-simple-children]\n" +"\n" +"This subsystem allows the creation of child config_items. These\n" +"items have only one attribute that is readable and writeable.\n"); +} + +static void simple_children_release(struct config_item *item) +{ + kfree(to_simple_children(item)); +} + +static struct configfs_item_operations simple_children_item_ops = { + .release = simple_children_release, + .show_attribute = simple_children_attr_show, +}; + +/* + * Note that, since no extra work is required on ->drop_item(), + * no ->drop_item() is provided. + */ +static struct configfs_group_operations simple_children_group_ops = { + .make_item = simple_children_make_item, +}; + +static struct config_item_type simple_children_type = { + .ct_item_ops = &simple_children_item_ops, + .ct_group_ops = &simple_children_group_ops, + .ct_attrs = simple_children_attrs, + .ct_owner = THIS_MODULE, +}; + +static struct configfs_subsystem simple_children_subsys = { + .su_group = { + .cg_item = { + .ci_namebuf = "02-simple-children", + .ci_type = &simple_children_type, + }, + }, +}; + + +/* ----------------------------------------------------------------- */ + +/* + * 03-group-children + * + * This example reuses the simple_children group from above. However, + * the simple_children group is not the subsystem itself, it is a + * child of the subsystem. Creation of a group in the subsystem creates + * a new simple_children group. That group can then have simple_child + * children of its own. + */ + +static struct config_group *group_children_make_group(struct config_group *group, const char *name) +{ + struct simple_children *simple_children; + + simple_children = kzalloc(sizeof(struct simple_children), + GFP_KERNEL); + if (!simple_children) + return ERR_PTR(-ENOMEM); + + config_group_init_type_name(&simple_children->group, name, + &simple_children_type); + + return &simple_children->group; +} + +static struct configfs_attribute group_children_attr_description = { + .ca_owner = THIS_MODULE, + .ca_name = "description", + .ca_mode = S_IRUGO, +}; + +static struct configfs_attribute *group_children_attrs[] = { + &group_children_attr_description, + NULL, +}; + +static ssize_t group_children_attr_show(struct config_item *item, + struct configfs_attribute *attr, + char *page) +{ + return sprintf(page, +"[03-group-children]\n" +"\n" +"This subsystem allows the creation of child config_groups. These\n" +"groups are like the subsystem simple-children.\n"); +} + +static struct configfs_item_operations group_children_item_ops = { + .show_attribute = group_children_attr_show, +}; + +/* + * Note that, since no extra work is required on ->drop_item(), + * no ->drop_item() is provided. + */ +static struct configfs_group_operations group_children_group_ops = { + .make_group = group_children_make_group, +}; + +static struct config_item_type group_children_type = { + .ct_item_ops = &group_children_item_ops, + .ct_group_ops = &group_children_group_ops, + .ct_attrs = group_children_attrs, + .ct_owner = THIS_MODULE, +}; + +static struct configfs_subsystem group_children_subsys = { + .su_group = { + .cg_item = { + .ci_namebuf = "03-group-children", + .ci_type = &group_children_type, + }, + }, +}; + +/* ----------------------------------------------------------------- */ + +/* + * We're now done with our subsystem definitions. + * For convenience in this module, here's a list of them all. It + * allows the init function to easily register them. Most modules + * will only have one subsystem, and will only call register_subsystem + * on it directly. + */ +static struct configfs_subsystem *example_subsys[] = { + &childless_subsys.subsys, + &simple_children_subsys, + &group_children_subsys, + NULL, +}; + +static int __init configfs_example_init(void) +{ + int ret; + int i; + struct configfs_subsystem *subsys; + + for (i = 0; example_subsys[i]; i++) { + subsys = example_subsys[i]; + + config_group_init(&subsys->su_group); + mutex_init(&subsys->su_mutex); + ret = configfs_register_subsystem(subsys); + if (ret) { + printk(KERN_ERR "Error %d while registering subsystem %s\n", + ret, + subsys->su_group.cg_item.ci_namebuf); + goto out_unregister; + } + } + + return 0; + +out_unregister: + for (; i >= 0; i--) { + configfs_unregister_subsystem(example_subsys[i]); + } + + return ret; +} + +static void __exit configfs_example_exit(void) +{ + int i; + + for (i = 0; example_subsys[i]; i++) { + configfs_unregister_subsystem(example_subsys[i]); + } +} + +module_init(configfs_example_init); +module_exit(configfs_example_exit); +MODULE_LICENSE("GPL"); diff --git a/Documentation/ftrace.txt b/Documentation/ftrace.txt index f218f61..d330fe3 100644 --- a/Documentation/ftrace.txt +++ b/Documentation/ftrace.txt @@ -4,6 +4,7 @@ Copyright 2008 Red Hat Inc. Author: Steven Rostedt License: The GNU Free Documentation License, Version 1.2 + (dual licensed under the GPL v2) Reviewers: Elias Oltmanns, Randy Dunlap, Andrew Morton, John Kacur, and David Teigland. diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737 index 8f44607..b1fe009 100644 --- a/Documentation/hwmon/dme1737 +++ b/Documentation/hwmon/dme1737 @@ -22,6 +22,10 @@ Module Parameters and PWM output control functions. Using this parameter shouldn't be required since the BIOS usually takes care of this. +* probe_all_addr: bool Include non-standard LPC addresses 0x162e and 0x164e + when probing for ISA devices. This is required for the + following boards: + - VIA EPIA SN18000 Note that there is no need to use this parameter if the driver loads without complaining. The driver will say so if it is necessary. diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85 index 9549237..6d41db7 100644 --- a/Documentation/hwmon/lm85 +++ b/Documentation/hwmon/lm85 @@ -96,11 +96,6 @@ initial testing of the ADM1027 it was 1.00 degC steps. Analog Devices has confirmed this "bug". The ADT7463 is reported to work as described in the documentation. The current lm85 driver does not show the offset register. -The ADT7463 has a THERM asserted counter. This counter has a 22.76ms -resolution and a range of 5.8 seconds. The driver implements a 32-bit -accumulator of the counter value to extend the range to over a year. The -counter will stay at it's max value until read. - See the vendor datasheets for more information. There is application note from National (AN-1260) with some additional information about the LM85. The Analog Devices datasheet is very detailed and describes a procedure for @@ -206,13 +201,15 @@ Configuration choices: The National LM85's have two vendor specific configuration features. Tach. mode and Spinup Control. For more details on these, -see the LM85 datasheet or Application Note AN-1260. +see the LM85 datasheet or Application Note AN-1260. These features +are not currently supported by the lm85 driver. The Analog Devices ADM1027 has several vendor specific enhancements. The number of pulses-per-rev of the fans can be set, Tach monitoring can be optimized for PWM operation, and an offset can be applied to the temperatures to compensate for systemic errors in the -measurements. +measurements. These features are not currently supported by the lm85 +driver. In addition to the ADM1027 features, the ADT7463 also has Tmin control and THERM asserted counts. Automatic Tmin control acts to adjust the diff --git a/Documentation/power/power_supply_class.txt b/Documentation/power/power_supply_class.txt index a8686e5..c6cd495 100644 --- a/Documentation/power/power_supply_class.txt +++ b/Documentation/power/power_supply_class.txt @@ -101,6 +101,10 @@ of charge when battery became full/empty". It also could mean "value of charge when battery considered full/empty at given conditions (temperature, age)". I.e. these attributes represents real thresholds, not design values. +CHARGE_COUNTER - the current charge counter (in µAh). This could easily +be negative; there is no empty or full value. It is only useful for +relative, time-based measurements. + ENERGY_FULL, ENERGY_EMPTY - same as above but for energy. CAPACITY - capacity in percents. diff --git a/Documentation/power/regulator/consumer.txt b/Documentation/power/regulator/consumer.txt new file mode 100644 index 0000000..82b7a43 --- /dev/null +++ b/Documentation/power/regulator/consumer.txt @@ -0,0 +1,182 @@ +Regulator Consumer Driver Interface +=================================== + +This text describes the regulator interface for consumer device drivers. +Please see overview.txt for a description of the terms used in this text. + + +1. Consumer Regulator Access (static & dynamic drivers) +======================================================= + +A consumer driver can get access to it's supply regulator by calling :- + +regulator = regulator_get(dev, "Vcc"); + +The consumer passes in it's struct device pointer and power supply ID. The core +then finds the correct regulator by consulting a machine specific lookup table. +If the lookup is successful then this call will return a pointer to the struct +regulator that supplies this consumer. + +To release the regulator the consumer driver should call :- + +regulator_put(regulator); + +Consumers can be supplied by more than one regulator e.g. codec consumer with +analog and digital supplies :- + +digital = regulator_get(dev, "Vcc"); /* digital core */ +analog = regulator_get(dev, "Avdd"); /* analog */ + +The regulator access functions regulator_get() and regulator_put() will +usually be called in your device drivers probe() and remove() respectively. + + +2. Regulator Output Enable & Disable (static & dynamic drivers) +==================================================================== + +A consumer can enable it's power supply by calling:- + +int regulator_enable(regulator); + +NOTE: The supply may already be enabled before regulator_enabled() is called. +This may happen if the consumer shares the regulator or the regulator has been +previously enabled by bootloader or kernel board initialization code. + +A consumer can determine if a regulator is enabled by calling :- + +int regulator_is_enabled(regulator); + +This will return > zero when the regulator is enabled. + + +A consumer can disable it's supply when no longer needed by calling :- + +int regulator_disable(regulator); + +NOTE: This may not disable the supply if it's shared with other consumers. The +regulator will only be disabled when the enabled reference count is zero. + +Finally, a regulator can be forcefully disabled in the case of an emergency :- + +int regulator_force_disable(regulator); + +NOTE: this will immediately and forcefully shutdown the regulator output. All +consumers will be powered off. + + +3. Regulator Voltage Control & Status (dynamic drivers) +====================================================== + +Some consumer drivers need to be able to dynamically change their supply +voltage to match system operating points. e.g. CPUfreq drivers can scale +voltage along with frequency to save power, SD drivers may need to select the +correct card voltage, etc. + +Consumers can control their supply voltage by calling :- + +int regulator_set_voltage(regulator, min_uV, max_uV); + +Where min_uV and max_uV are the minimum and maximum acceptable voltages in +microvolts. + +NOTE: this can be called when the regulator is enabled or disabled. If called +when enabled, then the voltage changes instantly, otherwise the voltage +configuration changes and the voltage is physically set when the regulator is +next enabled. + +The regulators configured voltage output can be found by calling :- + +int regulator_get_voltage(regulator); + +NOTE: get_voltage() will return the configured output voltage whether the +regulator is enabled or disabled and should NOT be used to determine regulator +output state. However this can be used in conjunction with is_enabled() to +determine the regulator physical output voltage. + + +4. Regulator Current Limit Control & Status (dynamic drivers) +=========================================================== + +Some consumer drivers need to be able to dynamically change their supply +current limit to match system operating points. e.g. LCD backlight driver can +change the current limit to vary the backlight brightness, USB drivers may want +to set the limit to 500mA when supplying power. + +Consumers can control their supply current limit by calling :- + +int regulator_set_current_limit(regulator, min_uV, max_uV); + +Where min_uA and max_uA are the minimum and maximum acceptable current limit in +microamps. + +NOTE: this can be called when the regulator is enabled or disabled. If called +when enabled, then the current limit changes instantly, otherwise the current +limit configuration changes and the current limit is physically set when the +regulator is next enabled. + +A regulators current limit can be found by calling :- + +int regulator_get_current_limit(regulator); + +NOTE: get_current_limit() will return the current limit whether the regulator +is enabled or disabled and should not be used to determine regulator current +load. + + +5. Regulator Operating Mode Control & Status (dynamic drivers) +============================================================= + +Some consumers can further save system power by changing the operating mode of +their supply regulator to be more efficient when the consumers operating state +changes. e.g. consumer driver is idle and subsequently draws less current + +Regulator operating mode can be changed indirectly or directly. + +Indirect operating mode control. +-------------------------------- +Consumer drivers can request a change in their supply regulator operating mode +by calling :- + +int regulator_set_optimum_mode(struct regulator *regulator, int load_uA); + +This will cause the core to recalculate the total load on the regulator (based +on all it's consumers) and change operating mode (if necessary and permitted) +to best match the current operating load. + +The load_uA value can be determined from the consumers datasheet. e.g.most +datasheets have tables showing the max current consumed in certain situations. + +Most consumers will use indirect operating mode control since they have no +knowledge of the regulator or whether the regulator is shared with other +consumers. + +Direct operating mode control. +------------------------------ +Bespoke or tightly coupled drivers may want to directly control regulator +operating mode depending on their operating point. This can be achieved by +calling :- + +int regulator_set_mode(struct regulator *regulator, unsigned int mode); +unsigned int regulator_get_mode(struct regulator *regulator); + +Direct mode will only be used by consumers that *know* about the regulator and +are not sharing the regulator with other consumers. + + +6. Regulator Events +=================== +Regulators can notify consumers of external events. Events could be received by +consumers under regulator stress or failure conditions. + +Consumers can register interest in regulator events by calling :- + +int regulator_register_notifier(struct regulator *regulator, + struct notifier_block *nb); + +Consumers can uregister interest by calling :- + +int regulator_unregister_notifier(struct regulator *regulator, + struct notifier_block *nb); + +Regulators use the kernel notifier framework to send event to thier interested +consumers. diff --git a/Documentation/power/regulator/machine.txt b/Documentation/power/regulator/machine.txt new file mode 100644 index 0000000..c9a3566 --- /dev/null +++ b/Documentation/power/regulator/machine.txt @@ -0,0 +1,101 @@ +Regulator Machine Driver Interface +=================================== + +The regulator machine driver interface is intended for board/machine specific +initialisation code to configure the regulator subsystem. Typical things that +machine drivers would do are :- + + 1. Regulator -> Device mapping. + 2. Regulator supply configuration. + 3. Power Domain constraint setting. + + + +1. Regulator -> device mapping +============================== +Consider the following machine :- + + Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V] + | + +-> [Consumer B @ 3.3V] + +The drivers for consumers A & B must be mapped to the correct regulator in +order to control their power supply. This mapping can be achieved in machine +initialisation code by calling :- + +int regulator_set_device_supply(const char *regulator, struct device *dev, + const char *supply); + +and is shown with the following code :- + +regulator_set_device_supply("Regulator-1", devB, "Vcc"); +regulator_set_device_supply("Regulator-2", devA, "Vcc"); + +This maps Regulator-1 to the 'Vcc' supply for Consumer B and maps Regulator-2 +to the 'Vcc' supply for Consumer A. + + +2. Regulator supply configuration. +================================== +Consider the following machine (again) :- + + Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V] + | + +-> [Consumer B @ 3.3V] + +Regulator-1 supplies power to Regulator-2. This relationship must be registered +with the core so that Regulator-1 is also enabled when Consumer A enables it's +supply (Regulator-2). + +This relationship can be register with the core via :- + +int regulator_set_supply(const char *regulator, const char *regulator_supply); + +In this example we would use the following code :- + +regulator_set_supply("Regulator-2", "Regulator-1"); + +Relationships can be queried by calling :- + +const char *regulator_get_supply(const char *regulator); + + +3. Power Domain constraint setting. +=================================== +Each power domain within a system has physical constraints on voltage and +current. This must be defined in software so that the power domain is always +operated within specifications. + +Consider the following machine (again) :- + + Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V] + | + +-> [Consumer B @ 3.3V] + +This gives us two regulators and two power domains: + + Domain 1: Regulator-2, Consumer B. + Domain 2: Consumer A. + +Constraints can be registered by calling :- + +int regulator_set_platform_constraints(const char *regulator, + struct regulation_constraints *constraints); + +The example is defined as follows :- + +struct regulation_constraints domain_1 = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, +}; + +struct regulation_constraints domain_2 = { + .min_uV = 1800000, + .max_uV = 2000000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + .valid_modes_mask = REGULATOR_MODE_NORMAL, +}; + +regulator_set_platform_constraints("Regulator-1", &domain_1); +regulator_set_platform_constraints("Regulator-2", &domain_2); diff --git a/Documentation/power/regulator/overview.txt b/Documentation/power/regulator/overview.txt new file mode 100644 index 0000000..bdcb332 --- /dev/null +++ b/Documentation/power/regulator/overview.txt @@ -0,0 +1,171 @@ +Linux voltage and current regulator framework +============================================= + +About +===== + +This framework is designed to provide a standard kernel interface to control +voltage and current regulators. + +The intention is to allow systems to dynamically control regulator power output +in order to save power and prolong battery life. This applies to both voltage +regulators (where voltage output is controllable) and current sinks (where +current limit is controllable). + +(C) 2008 Wolfson Microelectronics PLC. +Author: Liam Girdwood + + +Nomenclature +============ + +Some terms used in this document:- + + o Regulator - Electronic device that supplies power to other devices. + Most regulators can enable and disable their output whilst + some can control their output voltage and or current. + + Input Voltage -> Regulator -> Output Voltage + + + o PMIC - Power Management IC. An IC that contains numerous regulators + and often contains other susbsystems. + + + o Consumer - Electronic device that is supplied power by a regulator. + Consumers can be classified into two types:- + + Static: consumer does not change it's supply voltage or + current limit. It only needs to enable or disable it's + power supply. It's supply voltage is set by the hardware, + bootloader, firmware or kernel board initialisation code. + + Dynamic: consumer needs to change it's supply voltage or + current limit to meet operation demands. + + + o Power Domain - Electronic circuit that is supplied it's input power by the + output power of a regulator, switch or by another power + domain. + + The supply regulator may be behind a switch(s). i.e. + + Regulator -+-> Switch-1 -+-> Switch-2 --> [Consumer A] + | | + | +-> [Consumer B], [Consumer C] + | + +-> [Consumer D], [Consumer E] + + That is one regulator and three power domains: + + Domain 1: Switch-1, Consumers D & E. + Domain 2: Switch-2, Consumers B & C. + Domain 3: Consumer A. + + and this represents a "supplies" relationship: + + Domain-1 --> Domain-2 --> Domain-3. + + A power domain may have regulators that are supplied power + by other regulators. i.e. + + Regulator-1 -+-> Regulator-2 -+-> [Consumer A] + | + +-> [Consumer B] + + This gives us two regulators and two power domains: + + Domain 1: Regulator-2, Consumer B. + Domain 2: Consumer A. + + and a "supplies" relationship: + + Domain-1 --> Domain-2 + + + o Constraints - Constraints are used to define power levels for performance + and hardware protection. Constraints exist at three levels: + + Regulator Level: This is defined by the regulator hardware + operating parameters and is specified in the regulator + datasheet. i.e. + + - voltage output is in the range 800mV -> 3500mV. + - regulator current output limit is 20mA @ 5V but is + 10mA @ 10V. + + Power Domain Level: This is defined in software by kernel + level board initialisation code. It is used to constrain a + power domain to a particular power range. i.e. + + - Domain-1 voltage is 3300mV + - Domain-2 voltage is 1400mV -> 1600mV + - Domain-3 current limit is 0mA -> 20mA. + + Consumer Level: This is defined by consumer drivers + dynamically setting voltage or current limit levels. + + e.g. a consumer backlight driver asks for a current increase + from 5mA to 10mA to increase LCD illumination. This passes + to through the levels as follows :- + + Consumer: need to increase LCD brightness. Lookup and + request next current mA value in brightness table (the + consumer driver could be used on several different + personalities based upon the same reference device). + + Power Domain: is the new current limit within the domain + operating limits for this domain and system state (e.g. + battery power, USB power) + + Regulator Domains: is the new current limit within the + regulator operating parameters for input/ouput voltage. + + If the regulator request passes all the constraint tests + then the new regulator value is applied. + + +Design +====== + +The framework is designed and targeted at SoC based devices but may also be +relevant to non SoC devices and is split into the following four interfaces:- + + + 1. Consumer driver interface. + + This uses a similar API to the kernel clock interface in that consumer + drivers can get and put a regulator (like they can with clocks atm) and + get/set voltage, current limit, mode, enable and disable. This should + allow consumers complete control over their supply voltage and current + limit. This also compiles out if not in use so drivers can be reused in + systems with no regulator based power control. + + See Documentation/power/regulator/consumer.txt + + 2. Regulator driver interface. + + This allows regulator drivers to register their regulators and provide + operations to the core. It also has a notifier call chain for propagating + regulator events to clients. + + See Documentation/power/regulator/regulator.txt + + 3. Machine interface. + + This interface is for machine specific code and allows the creation of + voltage/current domains (with constraints) for each regulator. It can + provide regulator constraints that will prevent device damage through + overvoltage or over current caused by buggy client drivers. It also + allows the creation of a regulator tree whereby some regulators are + supplied by others (similar to a clock tree). + + See Documentation/power/regulator/machine.txt + + 4. Userspace ABI. + + The framework also exports a lot of useful voltage/current/opmode data to + userspace via sysfs. This could be used to help monitor device power + consumption and status. + + See Documentation/ABI/testing/regulator-sysfs.txt diff --git a/Documentation/power/regulator/regulator.txt b/Documentation/power/regulator/regulator.txt new file mode 100644 index 0000000..a690501 --- /dev/null +++ b/Documentation/power/regulator/regulator.txt @@ -0,0 +1,30 @@ +Regulator Driver Interface +========================== + +The regulator driver interface is relatively simple and designed to allow +regulator drivers to register their services with the core framework. + + +Registration +============ + +Drivers can register a regulator by calling :- + +struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc, + void *reg_data); + +This will register the regulators capabilities and operations the regulator +core. The core does not touch reg_data (private to regulator driver). + +Regulators can be unregistered by calling :- + +void regulator_unregister(struct regulator_dev *rdev); + + +Regulator Events +================ +Regulators can send events (e.g. over temp, under voltage, etc) to consumer +drivers by calling :- + +int regulator_notifier_call_chain(struct regulator_dev *rdev, + unsigned long event, void *data); diff --git a/Documentation/powerpc/00-INDEX b/Documentation/powerpc/00-INDEX index 3be84aa..29d839c 100644 --- a/Documentation/powerpc/00-INDEX +++ b/Documentation/powerpc/00-INDEX @@ -20,8 +20,6 @@ mpc52xx-device-tree-bindings.txt - MPC5200 Device Tree Bindings ppc_htab.txt - info about the Linux/PPC /proc/ppc_htab entry -SBC8260_memory_mapping.txt - - EST SBC8260 board info smp.txt - use and state info about Linux/PPC on MP machines sound.txt diff --git a/Documentation/powerpc/SBC8260_memory_mapping.txt b/Documentation/powerpc/SBC8260_memory_mapping.txt deleted file mode 100644 index e6e9ee0..0000000 --- a/Documentation/powerpc/SBC8260_memory_mapping.txt +++ /dev/null @@ -1,197 +0,0 @@ -Please mail me (Jon Diekema, diekema_jon@si.com or diekema@cideas.com) -if you have questions, comments or corrections. - - * EST SBC8260 Linux memory mapping rules - - http://www.estc.com/ - http://www.estc.com/products/boards/SBC8260-8240_ds.html - - Initial conditions: - ------------------- - - Tasks that need to be perform by the boot ROM before control is - transferred to zImage (compressed Linux kernel): - - - Define the IMMR to 0xf0000000 - - - Initialize the memory controller so that RAM is available at - physical address 0x00000000. On the SBC8260 is this 16M (64M) - SDRAM. - - - The boot ROM should only clear the RAM that it is using. - - The reason for doing this is to enhances the chances of a - successful post mortem on a Linux panic. One of the first - items to examine is the 16k (LOG_BUF_LEN) circular console - buffer called log_buf which is defined in kernel/printk.c. - - - To enhance boot ROM performance, the I-cache can be enabled. - - Date: Mon, 22 May 2000 14:21:10 -0700 - From: Neil Russell - - LiMon (LInux MONitor) runs with and starts Linux with MMU - off, I-cache enabled, D-cache disabled. The I-cache doesn't - need hints from the MMU to work correctly as the D-cache - does. No D-cache means no special code to handle devices in - the presence of cache (no snooping, etc). The use of the - I-cache means that the monitor can run acceptably fast - directly from ROM, rather than having to copy it to RAM. - - - Build the board information structure (see - include/asm-ppc/est8260.h for its definition) - - - The compressed Linux kernel (zImage) contains a bootstrap loader - that is position independent; you can load it into any RAM, - ROM or FLASH memory address >= 0x00500000 (above 5 MB), or - at its link address of 0x00400000 (4 MB). - - Note: If zImage is loaded at its link address of 0x00400000 (4 MB), - then zImage will skip the step of moving itself to - its link address. - - - Load R3 with the address of the board information structure - - - Transfer control to zImage - - - The Linux console port is SMC1, and the baud rate is controlled - from the bi_baudrate field of the board information structure. - On thing to keep in mind when picking the baud rate, is that - there is no flow control on the SMC ports. I would stick - with something safe and standard like 19200. - - On the EST SBC8260, the SMC1 port is on the COM1 connector of - the board. - - - EST SBC8260 defaults: - --------------------- - - Chip - Memory Sel Bus Use - --------------------- --- --- ---------------------------------- - 0x00000000-0x03FFFFFF CS2 60x (16M or 64M)/64M SDRAM - 0x04000000-0x04FFFFFF CS4 local 4M/16M SDRAM (soldered to the board) - 0x21000000-0x21000000 CS7 60x 1B/64K Flash present detect (from the flash SIMM) - 0x21000001-0x21000001 CS7 60x 1B/64K Switches (read) and LEDs (write) - 0x22000000-0x2200FFFF CS5 60x 8K/64K EEPROM - 0xFC000000-0xFCFFFFFF CS6 60x 2M/16M flash (8 bits wide, soldered to the board) - 0xFE000000-0xFFFFFFFF CS0 60x 4M/16M flash (SIMM) - - Notes: - ------ - - - The chip selects can map 32K blocks and up (powers of 2) - - - The SDRAM machine can handled up to 128Mbytes per chip select - - - Linux uses the 60x bus memory (the SDRAM DIMM) for the - communications buffers. - - - BATs can map 128K-256Mbytes each. There are four data BATs and - four instruction BATs. Generally the data and instruction BATs - are mapped the same. - - - The IMMR must be set above the kernel virtual memory addresses, - which start at 0xC0000000. Otherwise, the kernel may crash as - soon as you start any threads or processes due to VM collisions - in the kernel or user process space. - - - Details from Dan Malek on 10/29/1999: - - The user application virtual space consumes the first 2 Gbytes - (0x00000000 to 0x7FFFFFFF). The kernel virtual text starts at - 0xC0000000, with data following. There is a "protection hole" - between the end of kernel data and the start of the kernel - dynamically allocated space, but this space is still within - 0xCxxxxxxx. - - Obviously the kernel can't map any physical addresses 1:1 in - these ranges. - - - Details from Dan Malek on 5/19/2000: - - During the early kernel initialization, the kernel virtual - memory allocator is not operational. Prior to this KVM - initialization, we choose to map virtual to physical addresses - 1:1. That is, the kernel virtual address exactly matches the - physical address on the bus. These mappings are typically done - in arch/ppc/kernel/head.S, or arch/ppc/mm/init.c. Only - absolutely necessary mappings should be done at this time, for - example board control registers or a serial uart. Normal device - driver initialization should map resources later when necessary. - - Although platform dependent, and certainly the case for embedded - 8xx, traditionally memory is mapped at physical address zero, - and I/O devices above physical address 0x80000000. The lowest - and highest (above 0xf0000000) I/O addresses are traditionally - used for devices or registers we need to map during kernel - initialization and prior to KVM operation. For this reason, - and since it followed prior PowerPC platform examples, I chose - to map the embedded 8xx kernel to the 0xc0000000 virtual address. - This way, we can enable the MMU to map the kernel for proper - operation, and still map a few windows before the KVM is operational. - - On some systems, you could possibly run the kernel at the - 0x80000000 or any other virtual address. It just depends upon - mapping that must be done prior to KVM operational. You can never - map devices or kernel spaces that overlap with the user virtual - space. This is why default IMMR mapping used by most BDM tools - won't work. They put the IMMR at something like 0x10000000 or - 0x02000000 for example. You simply can't map these addresses early - in the kernel, and continue proper system operation. - - The embedded 8xx/82xx kernel is mature enough that all you should - need to do is map the IMMR someplace at or above 0xf0000000 and it - should boot far enough to get serial console messages and KGDB - connected on any platform. There are lots of other subtle memory - management design features that you simply don't need to worry - about. If you are changing functions related to MMU initialization, - you are likely breaking things that are known to work and are - heading down a path of disaster and frustration. Your changes - should be to make the flexibility of the processor fit Linux, - not force arbitrary and non-workable memory mappings into Linux. - - - You don't want to change KERNELLOAD or KERNELBASE, otherwise the - virtual memory and MMU code will get confused. - - arch/ppc/Makefile:KERNELLOAD = 0xc0000000 - - include/asm-ppc/page.h:#define PAGE_OFFSET 0xc0000000 - include/asm-ppc/page.h:#define KERNELBASE PAGE_OFFSET - - - RAM is at physical address 0x00000000, and gets mapped to - virtual address 0xC0000000 for the kernel. - - - Physical addresses used by the Linux kernel: - -------------------------------------------- - - 0x00000000-0x3FFFFFFF 1GB reserved for RAM - 0xF0000000-0xF001FFFF 128K IMMR 64K used for dual port memory, - 64K for 8260 registers - - - Logical addresses used by the Linux kernel: - ------------------------------------------- - - 0xF0000000-0xFFFFFFFF 256M BAT0 (IMMR: dual port RAM, registers) - 0xE0000000-0xEFFFFFFF 256M BAT1 (I/O space for custom boards) - 0xC0000000-0xCFFFFFFF 256M BAT2 (RAM) - 0xD0000000-0xDFFFFFFF 256M BAT3 (if RAM > 256MByte) - - - EST SBC8260 Linux mapping: - -------------------------- - - DBAT0, IBAT0, cache inhibited: - - Chip - Memory Sel Use - --------------------- --- --------------------------------- - 0xF0000000-0xF001FFFF n/a IMMR: dual port RAM, registers - - DBAT1, IBAT1, cache inhibited: - diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt index b35f348..2ea76d9 100644 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt +++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt @@ -7,6 +7,15 @@ Currently defined compatibles: - fsl,cpm2-scc-uart - fsl,qe-uart +Modem control lines connected to GPIO controllers are listed in the gpios +property as described in booting-without-of.txt, section IX.1 in the following +order: + +CTS, RTS, DCD, DSR, DTR, and RI. + +The gpios property is optional and can be left out when control lines are +not used. + Example: serial@11a00 { @@ -18,4 +27,6 @@ Example: interrupt-parent = <&PIC>; fsl,cpm-brg = <1>; fsl,cpm-command = <00800000>; + gpios = <&gpio_c 15 0 + &gpio_d 29 0>; }; diff --git a/Documentation/rfkill.txt b/Documentation/rfkill.txt index 0843ed0..28b6ec8 100644 --- a/Documentation/rfkill.txt +++ b/Documentation/rfkill.txt @@ -390,9 +390,10 @@ rfkill lines are inactive, it must return RFKILL_STATE_SOFT_BLOCKED if its soft rfkill input line is active. Only if none of the rfkill input lines are active, will it return RFKILL_STATE_UNBLOCKED. -If it doesn't implement the get_state() hook, it must make sure that its calls -to rfkill_force_state() are enough to keep the status always up-to-date, and it -must do a rfkill_force_state() on resume from sleep. +Since the device has a hardware rfkill line, it IS subject to state changes +external to rfkill. Therefore, the driver must make sure that it calls +rfkill_force_state() to keep the status always up-to-date, and it must do a +rfkill_force_state() on resume from sleep. Every time the driver gets a notification from the card that one of its rfkill lines changed state (polling might be needed on badly designed cards that don't @@ -422,13 +423,24 @@ of the hardware is unknown), or read-write (where the hardware can be queried about its current state). The rfkill class will call the get_state hook of a device every time it needs -to know the *real* current state of the hardware. This can happen often. +to know the *real* current state of the hardware. This can happen often, but +it does not do any polling, so it is not enough on hardware that is subject +to state changes outside of the rfkill subsystem. + +Therefore, calling rfkill_force_state() when a state change happens is +mandatory when the device has a hardware rfkill line, or when something else +like the firmware could cause its state to be changed without going through the +rfkill class. Some hardware provides events when its status changes. In these cases, it is best for the driver to not provide a get_state hook, and instead register the rfkill class *already* with the correct status, and keep it updated using rfkill_force_state() when it gets an event from the hardware. +rfkill_force_state() must be used on the device resume handlers to update the +rfkill status, should there be any chance of the device status changing during +the sleep. + There is no provision for a statically-allocated rfkill struct. You must use rfkill_allocate() to allocate one. diff --git a/MAINTAINERS b/MAINTAINERS index deedc0d..8223a52 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -502,6 +502,12 @@ L: openezx-devel@lists.openezx.org (subscribers-only) W: http://www.openezx.org/ S: Maintained +ARM/FREESCALE IMX / MXC ARM ARCHITECTURE +P: Sascha Hauer +M: kernel@pengutronix.de +L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) +S: Maintained + ARM/GLOMATION GESBC9312SX MACHINE SUPPORT P: Lennert Buytenhek M: kernel@wantstofly.org @@ -1878,13 +1884,9 @@ W: http://gigaset307x.sourceforge.net/ S: Maintained HARDWARE MONITORING -P: Mark M. Hoffman -M: mhoffman@lightlink.com L: lm-sensors@lm-sensors.org W: http://www.lm-sensors.org/ -T: git lm-sensors.org:/kernel/mhoffman/hwmon-2.6.git testing -T: git lm-sensors.org:/kernel/mhoffman/hwmon-2.6.git release -S: Maintained +S: Orphaned HARDWARE RANDOM NUMBER GENERATOR CORE S: Orphaned @@ -3968,7 +3970,7 @@ M: lethal@linux-sh.org L: linux-sh@vger.kernel.org W: http://www.linux-sh.org T: git kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.git -S: Maintained +S: Supported SUN3/3X P: Sam Creasey @@ -4504,6 +4506,15 @@ M: kaber@trash.net L: netdev@vger.kernel.org S: Maintained +VOLTAGE AND CURRENT REGULATOR FRAMEWORK +P: Liam Girdwood +M: lg@opensource.wolfsonmicro.com +P: Mark Brown +M: broonie@opensource.wolfsonmicro.com +W: http://opensource.wolfsonmicro.com/node/15 +T: git kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6.git +S: Supported + VT1211 HARDWARE MONITOR DRIVER P: Juerg Haefliger M: juergh@gmail.com diff --git a/Makefile b/Makefile index aa527a4..f156f40 100644 --- a/Makefile +++ b/Makefile @@ -930,7 +930,7 @@ ifneq ($(KBUILD_SRC),) /bin/false; \ fi; $(Q)if [ ! -d include2 ]; then mkdir -p include2; fi; - $(Q)if [ -e $(srctree)/include/asm-$(SRCARCH)/system.h ]; then \ + $(Q)if [ -e $(srctree)/include/asm-$(SRCARCH)/errno.h ]; then \ ln -fsn $(srctree)/include/asm-$(SRCARCH) include2/asm; \ fi endif diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 257033c..4b8acd2 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1225,6 +1225,8 @@ source "drivers/dma/Kconfig" source "drivers/dca/Kconfig" +source "drivers/regulator/Kconfig" + source "drivers/uio/Kconfig" endmenu diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile index 95baac4..94462a0 100644 --- a/arch/arm/boot/compressed/Makefile +++ b/arch/arm/boot/compressed/Makefile @@ -112,6 +112,3 @@ $(obj)/font.c: $(FONTC) $(obj)/vmlinux.lds: $(obj)/vmlinux.lds.in arch/arm/boot/Makefile .config @sed "$(SEDFLAGS)" < $< > $@ - -$(obj)/misc.o: $(obj)/misc.c include/asm/arch/uncompress.h lib/inflate.c - diff --git a/arch/arm/configs/at91cap9adk_defconfig b/arch/arm/configs/at91cap9adk_defconfig index be2b2f3..bf97801 100644 --- a/arch/arm/configs/at91cap9adk_defconfig +++ b/arch/arm/configs/at91cap9adk_defconfig @@ -170,7 +170,7 @@ CONFIG_MACH_AT91CAP9ADK=y # AT91 Board Options # CONFIG_MTD_AT91_DATAFLASH_CARD=y -# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set +# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set # # AT91 Feature Selections @@ -442,7 +442,7 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_ATMEL=y # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/at91sam9260ek_defconfig b/arch/arm/configs/at91sam9260ek_defconfig index 2011adf..38e6a0a 100644 --- a/arch/arm/configs/at91sam9260ek_defconfig +++ b/arch/arm/configs/at91sam9260ek_defconfig @@ -176,7 +176,7 @@ CONFIG_MACH_AT91SAM9260EK=y # AT91 Board Options # # CONFIG_MTD_AT91_DATAFLASH_CARD is not set -# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set +# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set # # AT91 Feature Selections diff --git a/arch/arm/configs/at91sam9261ek_defconfig b/arch/arm/configs/at91sam9261ek_defconfig index 4049768..93b779f 100644 --- a/arch/arm/configs/at91sam9261ek_defconfig +++ b/arch/arm/configs/at91sam9261ek_defconfig @@ -169,7 +169,7 @@ CONFIG_MACH_AT91SAM9261EK=y # AT91 Board Options # # CONFIG_MTD_AT91_DATAFLASH_CARD is not set -# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set +# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set # # AT91 Feature Selections @@ -433,7 +433,7 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_ATMEL=y # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/at91sam9263ek_defconfig b/arch/arm/configs/at91sam9263ek_defconfig index fa1c5ae..a7ddd94 100644 --- a/arch/arm/configs/at91sam9263ek_defconfig +++ b/arch/arm/configs/at91sam9263ek_defconfig @@ -169,7 +169,7 @@ CONFIG_MACH_AT91SAM9263EK=y # AT91 Board Options # CONFIG_MTD_AT91_DATAFLASH_CARD=y -# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set +# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set # # AT91 Feature Selections @@ -428,7 +428,7 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_ATMEL=y # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig index c068638..df0d6ee 100644 --- a/arch/arm/configs/at91sam9g20ek_defconfig +++ b/arch/arm/configs/at91sam9g20ek_defconfig @@ -168,7 +168,7 @@ CONFIG_MACH_AT91SAM9G20EK=y # AT91 Board Options # # CONFIG_MTD_AT91_DATAFLASH_CARD is not set -# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set +# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set # # AT91 Feature Selections @@ -442,10 +442,10 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y -CONFIG_MTD_NAND_AT91_ECC_SOFT=y -# CONFIG_MTD_NAND_AT91_ECC_HW is not set -# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +CONFIG_MTD_NAND_ATMEL=y +CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y +# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set +# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/at91sam9rlek_defconfig b/arch/arm/configs/at91sam9rlek_defconfig index d8ec5f9..1c76642 100644 --- a/arch/arm/configs/at91sam9rlek_defconfig +++ b/arch/arm/configs/at91sam9rlek_defconfig @@ -392,7 +392,7 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_ATMEL=y # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ONENAND is not set diff --git a/arch/arm/configs/cam60_defconfig b/arch/arm/configs/cam60_defconfig index f3cd4a9..f945105 100644 --- a/arch/arm/configs/cam60_defconfig +++ b/arch/arm/configs/cam60_defconfig @@ -466,10 +466,10 @@ CONFIG_MTD_NAND_VERIFY_WRITE=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y -# CONFIG_MTD_NAND_AT91_ECC_SOFT is not set -CONFIG_MTD_NAND_AT91_ECC_HW=y -# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +CONFIG_MTD_NAND_ATMEL=y +# CONFIG_MTD_NAND_ATMEL_ECC_SOFT is not set +CONFIG_MTD_NAND_ATMEL_ECC_HW=y +# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/qil-a9260_defconfig b/arch/arm/configs/qil-a9260_defconfig index ef903be..5cbd815 100644 --- a/arch/arm/configs/qil-a9260_defconfig +++ b/arch/arm/configs/qil-a9260_defconfig @@ -458,10 +458,10 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y -CONFIG_MTD_NAND_AT91_ECC_SOFT=y -# CONFIG_MTD_NAND_AT91_ECC_HW is not set -# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +CONFIG_MTD_NAND_ATMEL=y +CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y +# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set +# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/sam9_l9260_defconfig b/arch/arm/configs/sam9_l9260_defconfig index 8688362..1174e27 100644 --- a/arch/arm/configs/sam9_l9260_defconfig +++ b/arch/arm/configs/sam9_l9260_defconfig @@ -429,7 +429,7 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_ATMEL=y # CONFIG_MTD_NAND_NANDSIM is not set CONFIG_MTD_NAND_PLATFORM=y # CONFIG_MTD_ONENAND is not set diff --git a/arch/arm/configs/usb-a9260_defconfig b/arch/arm/configs/usb-a9260_defconfig index 3680bd2..fcb4aaa 100644 --- a/arch/arm/configs/usb-a9260_defconfig +++ b/arch/arm/configs/usb-a9260_defconfig @@ -458,10 +458,10 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y -CONFIG_MTD_NAND_AT91_ECC_SOFT=y -# CONFIG_MTD_NAND_AT91_ECC_HW is not set -# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +CONFIG_MTD_NAND_ATMEL=y +CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y +# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set +# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/usb-a9263_defconfig b/arch/arm/configs/usb-a9263_defconfig index 48d455b..b786e04 100644 --- a/arch/arm/configs/usb-a9263_defconfig +++ b/arch/arm/configs/usb-a9263_defconfig @@ -450,10 +450,10 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set -CONFIG_MTD_NAND_AT91=y -CONFIG_MTD_NAND_AT91_ECC_SOFT=y -# CONFIG_MTD_NAND_AT91_ECC_HW is not set -# CONFIG_MTD_NAND_AT91_ECC_NONE is not set +CONFIG_MTD_NAND_ATMEL=y +CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y +# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set +# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/configs/yl9200_defconfig b/arch/arm/configs/yl9200_defconfig index 26de37f..a9f41c2 100644 --- a/arch/arm/configs/yl9200_defconfig +++ b/arch/arm/configs/yl9200_defconfig @@ -421,7 +421,7 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_ECC_SMC is not set # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=y -CONFIG_MTD_NAND_AT91=y +CONFIG_MTD_NAND_ATMEL=y # CONFIG_MTD_NAND_NANDSIM is not set CONFIG_MTD_NAND_PLATFORM=y # CONFIG_MTD_ALAUDA is not set diff --git a/arch/arm/include/asm/Kbuild b/arch/arm/include/asm/Kbuild new file mode 100644 index 0000000..73237bd --- /dev/null +++ b/arch/arm/include/asm/Kbuild @@ -0,0 +1,3 @@ +include include/asm-generic/Kbuild.asm + +unifdef-y += hwcap.h diff --git a/arch/arm/include/asm/a.out-core.h b/arch/arm/include/asm/a.out-core.h new file mode 100644 index 0000000..93d04ac --- /dev/null +++ b/arch/arm/include/asm/a.out-core.h @@ -0,0 +1,49 @@ +/* a.out coredump register dumper + * + * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. + * Written by David Howells (dhowells@redhat.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public Licence + * as published by the Free Software Foundation; either version + * 2 of the Licence, or (at your option) any later version. + */ + +#ifndef _ASM_A_OUT_CORE_H +#define _ASM_A_OUT_CORE_H + +#ifdef __KERNEL__ + +#include +#include + +/* + * fill in the user structure for an a.out core dump + */ +static inline void aout_dump_thread(struct pt_regs *regs, struct user *dump) +{ + struct task_struct *tsk = current; + + dump->magic = CMAGIC; + dump->start_code = tsk->mm->start_code; + dump->start_stack = regs->ARM_sp & ~(PAGE_SIZE - 1); + + dump->u_tsize = (tsk->mm->end_code - tsk->mm->start_code) >> PAGE_SHIFT; + dump->u_dsize = (tsk->mm->brk - tsk->mm->start_data + PAGE_SIZE - 1) >> PAGE_SHIFT; + dump->u_ssize = 0; + + dump->u_debugreg[0] = tsk->thread.debug.bp[0].address; + dump->u_debugreg[1] = tsk->thread.debug.bp[1].address; + dump->u_debugreg[2] = tsk->thread.debug.bp[0].insn.arm; + dump->u_debugreg[3] = tsk->thread.debug.bp[1].insn.arm; + dump->u_debugreg[4] = tsk->thread.debug.nsaved; + + if (dump->start_stack < 0x04000000) + dump->u_ssize = (0x04000000 - dump->start_stack) >> PAGE_SHIFT; + + dump->regs = *regs; + dump->u_fpvalid = dump_fpu (regs, &dump->u_fp); +} + +#endif /* __KERNEL__ */ +#endif /* _ASM_A_OUT_CORE_H */ diff --git a/arch/arm/include/asm/a.out.h b/arch/arm/include/asm/a.out.h new file mode 100644 index 0000000..79489fd --- /dev/null +++ b/arch/arm/include/asm/a.out.h @@ -0,0 +1,34 @@ +#ifndef __ARM_A_OUT_H__ +#define __ARM_A_OUT_H__ + +#include +#include + +struct exec +{ + __u32 a_info; /* Use macros N_MAGIC, etc for access */ + __u32 a_text; /* length of text, in bytes */ + __u32 a_data; /* length of data, in bytes */ + __u32 a_bss; /* length of uninitialized data area for file, in bytes */ + __u32 a_syms; /* length of symbol table data in file, in bytes */ + __u32 a_entry; /* start address */ + __u32 a_trsize; /* length of relocation info for text, in bytes */ + __u32 a_drsize; /* length of relocation info for data, in bytes */ +}; + +/* + * This is always the same + */ +#define N_TXTADDR(a) (0x00008000) + +#define N_TRSIZE(a) ((a).a_trsize) +#define N_DRSIZE(a) ((a).a_drsize) +#define N_SYMSIZE(a) ((a).a_syms) + +#define M_ARM 103 + +#ifndef LIBRARY_START_TEXT +#define LIBRARY_START_TEXT (0x00c00000) +#endif + +#endif /* __A_OUT_GNU_H__ */ diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h new file mode 100644 index 0000000..6116e48 --- /dev/null +++ b/arch/arm/include/asm/assembler.h @@ -0,0 +1,116 @@ +/* + * arch/arm/include/asm/assembler.h + * + * Copyright (C) 1996-2000 Russell King + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This file contains arm architecture specific defines + * for the different processors. + * + * Do not include any C declarations in this file - it is included by + * assembler source. + */ +#ifndef __ASSEMBLY__ +#error "Only include this from assembly code" +#endif + +#include + +/* + * Endian independent macros for shifting bytes within registers. + */ +#ifndef __ARMEB__ +#define pull lsr +#define push lsl +#define get_byte_0 lsl #0 +#define get_byte_1 lsr #8 +#define get_byte_2 lsr #16 +#define get_byte_3 lsr #24 +#define put_byte_0 lsl #0 +#define put_byte_1 lsl #8 +#define put_byte_2 lsl #16 +#define put_byte_3 lsl #24 +#else +#define pull lsl +#define push lsr +#define get_byte_0 lsr #24 +#define get_byte_1 lsr #16 +#define get_byte_2 lsr #8 +#define get_byte_3 lsl #0 +#define put_byte_0 lsl #24 +#define put_byte_1 lsl #16 +#define put_byte_2 lsl #8 +#define put_byte_3 lsl #0 +#endif + +/* + * Data preload for architectures that support it + */ +#if __LINUX_ARM_ARCH__ >= 5 +#define PLD(code...) code +#else +#define PLD(code...) +#endif + +/* + * This can be used to enable code to cacheline align the destination + * pointer when bulk writing to memory. Experiments on StrongARM and + * XScale didn't show this a worthwhile thing to do when the cache is not + * set to write-allocate (this would need further testing on XScale when WA + * is used). + * + * On Feroceon there is much to gain however, regardless of cache mode. + */ +#ifdef CONFIG_CPU_FEROCEON +#define CALGN(code...) code +#else +#define CALGN(code...) +#endif + +/* + * Enable and disable interrupts + */ +#if __LINUX_ARM_ARCH__ >= 6 + .macro disable_irq + cpsid i + .endm + + .macro enable_irq + cpsie i + .endm +#else + .macro disable_irq + msr cpsr_c, #PSR_I_BIT | SVC_MODE + .endm + + .macro enable_irq + msr cpsr_c, #SVC_MODE + .endm +#endif + +/* + * Save the current IRQ state and disable IRQs. Note that this macro + * assumes FIQs are enabled, and that the processor is in SVC mode. + */ + .macro save_and_disable_irqs, oldcpsr + mrs \oldcpsr, cpsr + disable_irq + .endm + +/* + * Restore interrupt state previously stored in a register. We don't + * guarantee that this will preserve the flags. + */ + .macro restore_irqs, oldcpsr + msr cpsr_c, \oldcpsr + .endm + +#define USER(x...) \ +9999: x; \ + .section __ex_table,"a"; \ + .align 3; \ + .long 9999b,9001f; \ + .previous diff --git a/arch/arm/include/asm/atomic.h b/arch/arm/include/asm/atomic.h new file mode 100644 index 0000000..325f881 --- /dev/null +++ b/arch/arm/include/asm/atomic.h @@ -0,0 +1,212 @@ +/* + * arch/arm/include/asm/atomic.h + * + * Copyright (C) 1996 Russell King. + * Copyright (C) 2002 Deep Blue Solutions Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __ASM_ARM_ATOMIC_H +#define __ASM_ARM_ATOMIC_H + +#include +#include + +typedef struct { volatile int counter; } atomic_t; + +#define ATOMIC_INIT(i) { (i) } + +#ifdef __KERNEL__ + +#define atomic_read(v) ((v)->counter) + +#if __LINUX_ARM_ARCH__ >= 6 + +/* + * ARMv6 UP and SMP safe atomic ops. We use load exclusive and + * store exclusive to ensure that these are atomic. We may loop + * to ensure that the update happens. Writing to 'v->counter' + * without using the following operations WILL break the atomic + * nature of these ops. + */ +static inline void atomic_set(atomic_t *v, int i) +{ + unsigned long tmp; + + __asm__ __volatile__("@ atomic_set\n" +"1: ldrex %0, [%1]\n" +" strex %0, %2, [%1]\n" +" teq %0, #0\n" +" bne 1b" + : "=&r" (tmp) + : "r" (&v->counter), "r" (i) + : "cc"); +} + +static inline int atomic_add_return(int i, atomic_t *v) +{ + unsigned long tmp; + int result; + + __asm__ __volatile__("@ atomic_add_return\n" +"1: ldrex %0, [%2]\n" +" add %0, %0, %3\n" +" strex %1, %0, [%2]\n" +" teq %1, #0\n" +" bne 1b" + : "=&r" (result), "=&r" (tmp) + : "r" (&v->counter), "Ir" (i) + : "cc"); + + return result; +} + +static inline int atomic_sub_return(int i, atomic_t *v) +{ + unsigned long tmp; + int result; + + __asm__ __volatile__("@ atomic_sub_return\n" +"1: ldrex %0, [%2]\n" +" sub %0, %0, %3\n" +" strex %1, %0, [%2]\n" +" teq %1, #0\n" +" bne 1b" + : "=&r" (result), "=&r" (tmp) + : "r" (&v->counter), "Ir" (i) + : "cc"); + + return result; +} + +static inline int atomic_cmpxchg(atomic_t *ptr, int old, int new) +{ + unsigned long oldval, res; + + do { + __asm__ __volatile__("@ atomic_cmpxchg\n" + "ldrex %1, [%2]\n" + "mov %0, #0\n" + "teq %1, %3\n" + "strexeq %0, %4, [%2]\n" + : "=&r" (res), "=&r" (oldval) + : "r" (&ptr->counter), "Ir" (old), "r" (new) + : "cc"); + } while (res); + + return oldval; +} + +static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr) +{ + unsigned long tmp, tmp2; + + __asm__ __volatile__("@ atomic_clear_mask\n" +"1: ldrex %0, [%2]\n" +" bic %0, %0, %3\n" +" strex %1, %0, [%2]\n" +" teq %1, #0\n" +" bne 1b" + : "=&r" (tmp), "=&r" (tmp2) + : "r" (addr), "Ir" (mask) + : "cc"); +} + +#else /* ARM_ARCH_6 */ + +#include + +#ifdef CONFIG_SMP +#error SMP not supported on pre-ARMv6 CPUs +#endif + +#define atomic_set(v,i) (((v)->counter) = (i)) + +static inline int atomic_add_return(int i, atomic_t *v) +{ + unsigned long flags; + int val; + + raw_local_irq_save(flags); + val = v->counter; + v->counter = val += i; + raw_local_irq_restore(flags); + + return val; +} + +static inline int atomic_sub_return(int i, atomic_t *v) +{ + unsigned long flags; + int val; + + raw_local_irq_save(flags); + val = v->counter; + v->counter = val -= i; + raw_local_irq_restore(flags); + + return val; +} + +static inline int atomic_cmpxchg(atomic_t *v, int old, int new) +{ + int ret; + unsigned long flags; + + raw_local_irq_save(flags); + ret = v->counter; + if (likely(ret == old)) + v->counter = new; + raw_local_irq_restore(flags); + + return ret; +} + +static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr) +{ + unsigned long flags; + + raw_local_irq_save(flags); + *addr &= ~mask; + raw_local_irq_restore(flags); +} + +#endif /* __LINUX_ARM_ARCH__ */ + +#define atomic_xchg(v, new) (xchg(&((v)->counter), new)) + +static inline int atomic_add_unless(atomic_t *v, int a, int u) +{ + int c, old; + + c = atomic_read(v); + while (c != u && (old = atomic_cmpxchg((v), c, c + a)) != c) + c = old; + return c != u; +} +#define atomic_inc_not_zero(v) atomic_add_unless((v), 1, 0) + +#define atomic_add(i, v) (void) atomic_add_return(i, v) +#define atomic_inc(v) (void) atomic_add_return(1, v) +#define atomic_sub(i, v) (void) atomic_sub_return(i, v) +#define atomic_dec(v) (void) atomic_sub_return(1, v) + +#define atomic_inc_and_test(v) (atomic_add_return(1, v) == 0) +#define atomic_dec_and_test(v) (atomic_sub_return(1, v) == 0) +#define atomic_inc_return(v) (atomic_add_return(1, v)) +#define atomic_dec_return(v) (atomic_sub_return(1, v)) +#define atomic_sub_and_test(i, v) (atomic_sub_return(i, v) == 0) + +#define atomic_add_negative(i,v) (atomic_add_return(i, v) < 0) + +/* Atomic operations are already serializing on ARM */ +#define smp_mb__before_atomic_dec() barrier() +#define smp_mb__after_atomic_dec() barrier() +#define smp_mb__before_atomic_inc() barrier() +#define smp_mb__after_atomic_inc() barrier() + +#include +#endif +#endif diff --git a/arch/arm/include/asm/auxvec.h b/arch/arm/include/asm/auxvec.h new file mode 100644 index 0000000..c0536f6 --- /dev/null +++ b/arch/arm/include/asm/auxvec.h @@ -0,0 +1,4 @@ +#ifndef __ASMARM_AUXVEC_H +#define __ASMARM_AUXVEC_H + +#endif diff --git a/arch/arm/include/asm/bitops.h b/arch/arm/include/asm/bitops.h new file mode 100644 index 0000000..9a1db20 --- /dev/null +++ b/arch/arm/include/asm/bitops.h @@ -0,0 +1,340 @@ +/* + * Copyright 1995, Russell King. + * Various bits and pieces copyrights include: + * Linus Torvalds (test_bit). + * Big endian support: Copyright 2001, Nicolas Pitre + * reworked by rmk. + * + * bit 0 is the LSB of an "unsigned long" quantity. + * + * Please note that the code in this file should never be included + * from user space. Many of these are not implemented in assembler + * since they would be too costly. Also, they require privileged + * instructions (which are not available from user mode) to ensure + * that they are atomic. + */ + +#ifndef __ASM_ARM_BITOPS_H +#define __ASM_ARM_BITOPS_H + +#ifdef __KERNEL__ + +#ifndef _LINUX_BITOPS_H +#error only can be included directly +#endif + +#include +#include + +#define smp_mb__before_clear_bit() mb() +#define smp_mb__after_clear_bit() mb() + +/* + * These functions are the basis of our bit ops. + * + * First, the atomic bitops. These use native endian. + */ +static inline void ____atomic_set_bit(unsigned int bit, volatile unsigned long *p) +{ + unsigned long flags; + unsigned long mask = 1UL << (bit & 31); + + p += bit >> 5; + + raw_local_irq_save(flags); + *p |= mask; + raw_local_irq_restore(flags); +} + +static inline void ____atomic_clear_bit(unsigned int bit, volatile unsigned long *p) +{ + unsigned long flags; + unsigned long mask = 1UL << (bit & 31); + + p += bit >> 5; + + raw_local_irq_save(flags); + *p &= ~mask; + raw_local_irq_restore(flags); +} + +static inline void ____atomic_change_bit(unsigned int bit, volatile unsigned long *p) +{ + unsigned long flags; + unsigned long mask = 1UL << (bit & 31); + + p += bit >> 5; + + raw_local_irq_save(flags); + *p ^= mask; + raw_local_irq_restore(flags); +} + +static inline int +____atomic_test_and_set_bit(unsigned int bit, volatile unsigned long *p) +{ + unsigned long flags; + unsigned int res; + unsigned long mask = 1UL << (bit & 31); + + p += bit >> 5; + + raw_local_irq_save(flags); + res = *p; + *p = res | mask; + raw_local_irq_restore(flags); + + return res & mask; +} + +static inline int +____atomic_test_and_clear_bit(unsigned int bit, volatile unsigned long *p) +{ + unsigned long flags; + unsigned int res; + unsigned long mask = 1UL << (bit & 31); + + p += bit >> 5; + + raw_local_irq_save(flags); + res = *p; + *p = res & ~mask; + raw_local_irq_restore(flags); + + return res & mask; +} + +static inline int +____atomic_test_and_change_bit(unsigned int bit, volatile unsigned long *p) +{ + unsigned long flags; + unsigned int res; + unsigned long mask = 1UL << (bit & 31); + + p += bit >> 5; + + raw_local_irq_save(flags); + res = *p; + *p = res ^ mask; + raw_local_irq_restore(flags); + + return res & mask; +} + +#include + +/* + * A note about Endian-ness. + * ------------------------- + * + * When the ARM is put into big endian mode via CR15, the processor + * merely swaps the order of bytes within words, thus: + * + * ------------ physical data bus bits ----------- + * D31 ... D24 D23 ... D16 D15 ... D8 D7 ... D0 + * little byte 3 byte 2 byte 1 byte 0 + * big byte 0 byte 1 byte 2 byte 3 + * + * This means that reading a 32-bit word at address 0 returns the same + * value irrespective of the endian mode bit. + * + * Peripheral devices should be connected with the data bus reversed in + * "Big Endian" mode. ARM Application Note 61 is applicable, and is + * available from http://www.arm.com/. + * + * The following assumes that the data bus connectivity for big endian + * mode has been followed. + * + * Note that bit 0 is defined to be 32-bit word bit 0, not byte 0 bit 0. + */ + +/* + * Little endian assembly bitops. nr = 0 -> byte 0 bit 0. + */ +extern void _set_bit_le(int nr, volatile unsigned long * p); +extern void _clear_bit_le(int nr, volatile unsigned long * p); +extern void _change_bit_le(int nr, volatile unsigned long * p); +extern int _test_and_set_bit_le(int nr, volatile unsigned long * p); +extern int _test_and_clear_bit_le(int nr, volatile unsigned long * p); +extern int _test_and_change_bit_le(int nr, volatile unsigned long * p); +extern int _find_first_zero_bit_le(const void * p, unsigned size); +extern int _find_next_zero_bit_le(const void * p, int size, int offset); +extern int _find_first_bit_le(const unsigned long *p, unsigned size); +extern int _find_next_bit_le(const unsigned long *p, int size, int offset); + +/* + * Big endian assembly bitops. nr = 0 -> byte 3 bit 0. + */ +extern void _set_bit_be(int nr, volatile unsigned long * p); +extern void _clear_bit_be(int nr, volatile unsigned long * p); +extern void _change_bit_be(int nr, volatile unsigned long * p); +extern int _test_and_set_bit_be(int nr, volatile unsigned long * p); +extern int _test_and_clear_bit_be(int nr, volatile unsigned long * p); +extern int _test_and_change_bit_be(int nr, volatile unsigned long * p); +extern int _find_first_zero_bit_be(const void * p, unsigned size); +extern int _find_next_zero_bit_be(const void * p, int size, int offset); +extern int _find_first_bit_be(const unsigned long *p, unsigned size); +extern int _find_next_bit_be(const unsigned long *p, int size, int offset); + +#ifndef CONFIG_SMP +/* + * The __* form of bitops are non-atomic and may be reordered. + */ +#define ATOMIC_BITOP_LE(name,nr,p) \ + (__builtin_constant_p(nr) ? \ + ____atomic_##name(nr, p) : \ + _##name##_le(nr,p)) + +#define ATOMIC_BITOP_BE(name,nr,p) \ + (__builtin_constant_p(nr) ? \ + ____atomic_##name(nr, p) : \ + _##name##_be(nr,p)) +#else +#define ATOMIC_BITOP_LE(name,nr,p) _##name##_le(nr,p) +#define ATOMIC_BITOP_BE(name,nr,p) _##name##_be(nr,p) +#endif + +#define NONATOMIC_BITOP(name,nr,p) \ + (____nonatomic_##name(nr, p)) + +#ifndef __ARMEB__ +/* + * These are the little endian, atomic definitions. + */ +#define set_bit(nr,p) ATOMIC_BITOP_LE(set_bit,nr,p) +#define clear_bit(nr,p) ATOMIC_BITOP_LE(clear_bit,nr,p) +#define change_bit(nr,p) ATOMIC_BITOP_LE(change_bit,nr,p) +#define test_and_set_bit(nr,p) ATOMIC_BITOP_LE(test_and_set_bit,nr,p) +#define test_and_clear_bit(nr,p) ATOMIC_BITOP_LE(test_and_clear_bit,nr,p) +#define test_and_change_bit(nr,p) ATOMIC_BITOP_LE(test_and_change_bit,nr,p) +#define find_first_zero_bit(p,sz) _find_first_zero_bit_le(p,sz) +#define find_next_zero_bit(p,sz,off) _find_next_zero_bit_le(p,sz,off) +#define find_first_bit(p,sz) _find_first_bit_le(p,sz) +#define find_next_bit(p,sz,off) _find_next_bit_le(p,sz,off) + +#define WORD_BITOFF_TO_LE(x) ((x)) + +#else + +/* + * These are the big endian, atomic definitions. + */ +#define set_bit(nr,p) ATOMIC_BITOP_BE(set_bit,nr,p) +#define clear_bit(nr,p) ATOMIC_BITOP_BE(clear_bit,nr,p) +#define change_bit(nr,p) ATOMIC_BITOP_BE(change_bit,nr,p) +#define test_and_set_bit(nr,p) ATOMIC_BITOP_BE(test_and_set_bit,nr,p) +#define test_and_clear_bit(nr,p) ATOMIC_BITOP_BE(test_and_clear_bit,nr,p) +#define test_and_change_bit(nr,p) ATOMIC_BITOP_BE(test_and_change_bit,nr,p) +#define find_first_zero_bit(p,sz) _find_first_zero_bit_be(p,sz) +#define find_next_zero_bit(p,sz,off) _find_next_zero_bit_be(p,sz,off) +#define find_first_bit(p,sz) _find_first_bit_be(p,sz) +#define find_next_bit(p,sz,off) _find_next_bit_be(p,sz,off) + +#define WORD_BITOFF_TO_LE(x) ((x) ^ 0x18) + +#endif + +#if __LINUX_ARM_ARCH__ < 5 + +#include +#include +#include +#include + +#else + +static inline int constant_fls(int x) +{ + int r = 32; + + if (!x) + return 0; + if (!(x & 0xffff0000u)) { + x <<= 16; + r -= 16; + } + if (!(x & 0xff000000u)) { + x <<= 8; + r -= 8; + } + if (!(x & 0xf0000000u)) { + x <<= 4; + r -= 4; + } + if (!(x & 0xc0000000u)) { + x <<= 2; + r -= 2; + } + if (!(x & 0x80000000u)) { + x <<= 1; + r -= 1; + } + return r; +} + +/* + * On ARMv5 and above those functions can be implemented around + * the clz instruction for much better code efficiency. + */ + +#define __fls(x) \ + ( __builtin_constant_p(x) ? constant_fls(x) : \ + ({ int __r; asm("clz\t%0, %1" : "=r"(__r) : "r"(x) : "cc"); 32-__r; }) ) + +/* Implement fls() in C so that 64-bit args are suitably truncated */ +static inline int fls(int x) +{ + return __fls(x); +} + +#define ffs(x) ({ unsigned long __t = (x); fls(__t & -__t); }) +#define __ffs(x) (ffs(x) - 1) +#define ffz(x) __ffs( ~(x) ) + +#endif + +#include + +#include +#include +#include + +/* + * Ext2 is defined to use little-endian byte ordering. + * These do not need to be atomic. + */ +#define ext2_set_bit(nr,p) \ + __test_and_set_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define ext2_set_bit_atomic(lock,nr,p) \ + test_and_set_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define ext2_clear_bit(nr,p) \ + __test_and_clear_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define ext2_clear_bit_atomic(lock,nr,p) \ + test_and_clear_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define ext2_test_bit(nr,p) \ + test_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define ext2_find_first_zero_bit(p,sz) \ + _find_first_zero_bit_le(p,sz) +#define ext2_find_next_zero_bit(p,sz,off) \ + _find_next_zero_bit_le(p,sz,off) +#define ext2_find_next_bit(p, sz, off) \ + _find_next_bit_le(p, sz, off) + +/* + * Minix is defined to use little-endian byte ordering. + * These do not need to be atomic. + */ +#define minix_set_bit(nr,p) \ + __set_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define minix_test_bit(nr,p) \ + test_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define minix_test_and_set_bit(nr,p) \ + __test_and_set_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define minix_test_and_clear_bit(nr,p) \ + __test_and_clear_bit(WORD_BITOFF_TO_LE(nr), (unsigned long *)(p)) +#define minix_find_first_zero_bit(p,sz) \ + _find_first_zero_bit_le(p,sz) + +#endif /* __KERNEL__ */ + +#endif /* _ARM_BITOPS_H */ diff --git a/arch/arm/include/asm/bug.h b/arch/arm/include/asm/bug.h new file mode 100644 index 0000000..7b62351 --- /dev/null +++ b/arch/arm/include/asm/bug.h @@ -0,0 +1,24 @@ +#ifndef _ASMARM_BUG_H +#define _ASMARM_BUG_H + + +#ifdef CONFIG_BUG +#ifdef CONFIG_DEBUG_BUGVERBOSE +extern void __bug(const char *file, int line) __attribute__((noreturn)); + +/* give file/line information */ +#define BUG() __bug(__FILE__, __LINE__) + +#else + +/* this just causes an oops */ +#define BUG() (*(int *)0 = 0) + +#endif + +#define HAVE_ARCH_BUG +#endif + +#include + +#endif diff --git a/arch/arm/include/asm/bugs.h b/arch/arm/include/asm/bugs.h new file mode 100644 index 0000000..a97f1ea --- /dev/null +++ b/arch/arm/include/asm/bugs.h @@ -0,0 +1,21 @@ +/* + * arch/arm/include/asm/bugs.h + * + * Copyright (C) 1995-2003 Russell King + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __ASM_BUGS_H +#define __ASM_BUGS_H + +#ifdef CONFIG_MMU +extern void check_writebuffer_bugs(void); + +#define check_bugs() check_writebuffer_bugs() +#else +#define check_bugs() do { } while (0) +#endif + +#endif diff --git a/arch/arm/include/asm/byteorder.h b/arch/arm/include/asm/byteorder.h new file mode 100644 index 0000000..4fbfb22 --- /dev/null +++ b/arch/arm/include/asm/byteorder.h @@ -0,0 +1,58 @@ +/* + * arch/arm/include/asm/byteorder.h + * + * ARM Endian-ness. In little endian mode, the data bus is connected such + * that byte accesses appear as: + * 0 = d0...d7, 1 = d8...d15, 2 = d16...d23, 3 = d24...d31 + * and word accesses (data or instruction) appear as: + * d0...d31 + * + * When in big endian mode, byte accesses appear as: + * 0 = d24...d31, 1 = d16...d23, 2 = d8...d15, 3 = d0...d7 + * and word accesses (data or instruction) appear as: + * d0...d31 + */ +#ifndef __ASM_ARM_BYTEORDER_H +#define __ASM_ARM_BYTEORDER_H + +#include +#include + +static inline __attribute_const__ __u32 ___arch__swab32(__u32 x) +{ + __u32 t; + +#ifndef __thumb__ + if (!__builtin_constant_p(x)) { + /* + * The compiler needs a bit of a hint here to always do the + * right thing and not screw it up to different degrees + * depending on the gcc version. + */ + asm ("eor\t%0, %1, %1, ror #16" : "=r" (t) : "r" (x)); + } else +#endif + t = x ^ ((x << 16) | (x >> 16)); /* eor r1,r0,r0,ror #16 */ + + x = (x << 24) | (x >> 8); /* mov r0,r0,ror #8 */ + t &= ~0x00FF0000; /* bic r1,r1,#0x00FF0000 */ + x ^= (t >> 8); /* eor r0,r0,r1,lsr #8 */ + + return x; +} + +#define __arch__swab32(x) ___arch__swab32(x) + +#if !defined(__STRICT_ANSI__) || defined(__KERNEL__) +# define __BYTEORDER_HAS_U64__ +# define __SWAB_64_THRU_32__ +#endif + +#ifdef __ARMEB__ +#include +#else +#include +#endif + +#endif + diff --git a/arch/arm/include/asm/cache.h b/arch/arm/include/asm/cache.h new file mode 100644 index 0000000..cb7a9e9 --- /dev/null +++ b/arch/arm/include/asm/cache.h @@ -0,0 +1,10 @@ +/* + * arch/arm/include/asm/cache.h + */ +#ifndef __ASMARM_CACHE_H +#define __ASMARM_CACHE_H + +#define L1_CACHE_SHIFT 5 +#define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT) + +#endif diff --git a/arch/arm/include/asm/cacheflush.h b/arch/arm/include/asm/cacheflush.h new file mode 100644 index 0000000..9073d9c --- /dev/null +++ b/arch/arm/include/asm/cacheflush.h @@ -0,0 +1,537 @@ +/* + * arch/arm/include/asm/cacheflush.h + * + * Copyright (C) 1999-2002 Russell King + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef _ASMARM_CACHEFLUSH_H +#define _ASMARM_CACHEFLUSH_H + +#include +#include + +#include +#include + +#define CACHE_COLOUR(vaddr) ((vaddr & (SHMLBA - 1)) >> PAGE_SHIFT) + +/* + * Cache Model + * =========== + */ +#undef _CACHE +#undef MULTI_CACHE + +#if defined(CONFIG_CPU_CACHE_V3) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE v3 +# endif +#endif + +#if defined(CONFIG_CPU_CACHE_V4) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE v4 +# endif +#endif + +#if defined(CONFIG_CPU_ARM920T) || defined(CONFIG_CPU_ARM922T) || \ + defined(CONFIG_CPU_ARM925T) || defined(CONFIG_CPU_ARM1020) +# define MULTI_CACHE 1 +#endif + +#if defined(CONFIG_CPU_ARM926T) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE arm926 +# endif +#endif + +#if defined(CONFIG_CPU_ARM940T) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE arm940 +# endif +#endif + +#if defined(CONFIG_CPU_ARM946E) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE arm946 +# endif +#endif + +#if defined(CONFIG_CPU_CACHE_V4WB) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE v4wb +# endif +#endif + +#if defined(CONFIG_CPU_XSCALE) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE xscale +# endif +#endif + +#if defined(CONFIG_CPU_XSC3) +# ifdef _CACHE +# define MULTI_CACHE 1 +# else +# define _CACHE xsc3 +# endif +#endif + +#if defined(CONFIG_CPU_FEROCEON) +# define MULTI_CACHE 1 +#endif + +#if defined(CONFIG_CPU_V6) +//# ifdef _CACHE +# define MULTI_CACHE 1 +//# else +//# define _CACHE v6 +//# endif +#endif + +#if defined(CONFIG_CPU_V7) +//# ifdef _CACHE +# define MULTI_CACHE 1 +//# else +//# define _CACHE v7 +//# endif +#endif + +#if !defined(_CACHE) && !defined(MULTI_CACHE) +#error Unknown cache maintainence model +#endif + +/* + * This flag is used to indicate that the page pointed to by a pte + * is dirty and requires cleaning before returning it to the user. + */ +#define PG_dcache_dirty PG_arch_1 + +/* + * MM Cache Management + * =================== + * + * The arch/arm/mm/cache-*.S and arch/arm/mm/proc-*.S files + * implement these methods. + * + * Start addresses are inclusive and end addresses are exclusive; + * start addresses should be rounded down, end addresses up. + * + * See Documentation/cachetlb.txt for more information. + * Please note that the implementation of these, and the required + * effects are cache-type (VIVT/VIPT/PIPT) specific. + * + * flush_cache_kern_all() + * + * Unconditionally clean and invalidate the entire cache. + * + * flush_cache_user_mm(mm) + * + * Clean and invalidate all user space cache entries + * before a change of page tables. + * + * flush_cache_user_range(start, end, flags) + * + * Clean and invalidate a range of cache entries in the + * specified address space before a change of page tables. + * - start - user start address (inclusive, page aligned) + * - end - user end address (exclusive, page aligned) + * - flags - vma->vm_flags field + * + * coherent_kern_range(start, end) + * + * Ensure coherency between the Icache and the Dcache in the + * region described by start, end. If you have non-snooping + * Harvard caches, you need to implement this function. + * - start - virtual start address + * - end - virtual end address + * + * DMA Cache Coherency + * =================== + * + * dma_inv_range(start, end) + * + * Invalidate (discard) the specified virtual address range. + * May not write back any entries. If 'start' or 'end' + * are not cache line aligned, those lines must be written + * back. + * - start - virtual start address + * - end - virtual end address + * + * dma_clean_range(start, end) + * + * Clean (write back) the specified virtual address range. + * - start - virtual start address + * - end - virtual end address + * + * dma_flush_range(start, end) + * + * Clean and invalidate the specified virtual address range. + * - start - virtual start address + * - end - virtual end address + */ + +struct cpu_cache_fns { + void (*flush_kern_all)(void); + void (*flush_user_all)(void); + void (*flush_user_range)(unsigned long, unsigned long, unsigned int); + + void (*coherent_kern_range)(unsigned long, unsigned long); + void (*coherent_user_range)(unsigned long, unsigned long); + void (*flush_kern_dcache_page)(void *); + + void (*dma_inv_range)(const void *, const void *); + void (*dma_clean_range)(const void *, const void *); + void (*dma_flush_range)(const void *, const void *); +}; + +struct outer_cache_fns { + void (*inv_range)(unsigned long, unsigned long); + void (*clean_range)(unsigned long, unsigned long); + void (*flush_range)(unsigned long, unsigned long); +}; + +/* + * Select the calling method + */ +#ifdef MULTI_CACHE + +extern struct cpu_cache_fns cpu_cache; + +#define __cpuc_flush_kern_all cpu_cache.flush_kern_all +#define __cpuc_flush_user_all cpu_cache.flush_user_all +#define __cpuc_flush_user_range cpu_cache.flush_user_range +#define __cpuc_coherent_kern_range cpu_cache.coherent_kern_range +#define __cpuc_coherent_user_range cpu_cache.coherent_user_range +#define __cpuc_flush_dcache_page cpu_cache.flush_kern_dcache_page + +/* + * These are private to the dma-mapping API. Do not use directly. + * Their sole purpose is to ensure that data held in the cache + * is visible to DMA, or data written by DMA to system memory is + * visible to the CPU. + */ +#define dmac_inv_range cpu_cache.dma_inv_range +#define dmac_clean_range cpu_cache.dma_clean_range +#define dmac_flush_range cpu_cache.dma_flush_range + +#else + +#define __cpuc_flush_kern_all __glue(_CACHE,_flush_kern_cache_all) +#define __cpuc_flush_user_all __glue(_CACHE,_flush_user_cache_all) +#define __cpuc_flush_user_range __glue(_CACHE,_flush_user_cache_range) +#define __cpuc_coherent_kern_range __glue(_CACHE,_coherent_kern_range) +#define __cpuc_coherent_user_range __glue(_CACHE,_coherent_user_range) +#define __cpuc_flush_dcache_page __glue(_CACHE,_flush_kern_dcache_page) + +extern void __cpuc_flush_kern_all(void); +extern void __cpuc_flush_user_all(void); +extern void __cpuc_flush_user_range(unsigned long, unsigned long, unsigned int); +extern void __cpuc_coherent_kern_range(unsigned long, unsigned long); +extern void __cpuc_coherent_user_range(unsigned long, unsigned long); +extern void __cpuc_flush_dcache_page(void *); + +/* + * These are private to the dma-mapping API. Do not use directly. + * Their sole purpose is to ensure that data held in the cache + * is visible to DMA, or data written by DMA to system memory is + * visible to the CPU. + */ +#define dmac_inv_range __glue(_CACHE,_dma_inv_range) +#define dmac_clean_range __glue(_CACHE,_dma_clean_range) +#define dmac_flush_range __glue(_CACHE,_dma_flush_range) + +extern void dmac_inv_range(const void *, const void *); +extern void dmac_clean_range(const void *, const void *); +extern void dmac_flush_range(const void *, const void *); + +#endif + +#ifdef C